Nissan Murano: Transaxle & Transmission :: Cvt: Re0f10j / Dtc/circuit Diagnosis
Nissan Murano (Z52) 2015-2024 Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f10j / Dtc/circuit Diagnosis
- U0073 Communication Bus a Off
- U0100 Lost Communication (ecm A)
- U0102 Lost Communication (transfer)
- U0122 Lost Communication (vdc)
- U0300 Can Communication Data
- U1000 Can Comm Circuit
- P0605 Control Module Rom
- P062f Eeprom
- P0705 Transmission Range Sensor a
- P0706 Transmission Range Sensor a
- P0711 Transmission Fluid Temperature Sensor a
- P0712 Transmission Fluid Temperature Sensor a
- P0715 Input Speed Sensor a
- P0740 Torque Converter
- P0741 Torque Converter
- P0742 Torque Converter
- P0746 Pressure Control Solenoid a
- P0776 Pressure Control Solenoid B
- P0778 Pressure Control Solenoid B
- P0794 Intermediate Speed Sensor a
- P0826 up and Down Shift Sw
- P0841 Transmission Fluid Pressure Sen/sw a
- P0847 Transmission Fluid Pressure Sen/sw B
- P0863 Tcm Communication
- P0890 Tcm
- P0894 Transmission Component Slipping
- P0965 Pressure Control Solenoid B
- P0966 Pressure Control Solenoid B
- P1588 Decel G Sensor
- P17f0 Cvt Judder (t/m Inspection)
- P17f1 Cvt Judder (c/v Inspection)
- P17f2 Cvt Judder (t/c Inspection)
- P2758 Tcc Pressure Control Solenoid
- P2765 Input Speed Sensor B
- P2813 Select Solenoid
- P2814 Select Solenoid
- Main Power Supply and Ground Circuit
- Shift Position Indicator Circuit
- Shift Lock System
How to Erase Permanent Dtc
Description
OUTLINEPermanent DTC is erased with MIL shutoff if the same malfunction is not detected after performing the driving pattern for MIL shutoff three times...
U0073 Communication Bus a Off
DTC Description
DTC DETECTION LOGICTCM communication blockage lasts for 2 seconds or more when turning ON the ignition switch. (Communication not established...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Stall Test
Work Procedure INSPECTIONCheck the engine oil level. Replenish if necessary. Refer to Inspection. Check for leak of the CVT fluid. Refer to Inspection. Drive for about 10 minutes to warm up the Nissan Murano vehicle so that the CVT fluid temperature is 50 to 80°C (122 to 176°F)...
Nissan Murano (Z52) 2015-2024 Service Manual: B260a Ignition Relay
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition B260A IGNITION RELAY (Ignition relay) Diagnosis condition When ignition switch ON. Signal (terminal) — Threshold — Diagnosis delay time 2 seconds or more POSSIBLE CAUSE Harness or connectors BCM IPDM E/R FAIL SAFE— DTC Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Ignition switch ON under the following conditions and wait for at least 2 seconds: CVT selector lever is in the P (park) or N (neutral) position...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Tire rotation
- Warning lights
- Passenger compartment
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
Copyright © 2026 www.nimurano.com