Nissan Murano: Dtc/circuit Diagnosis / P0706 Transmission Range Sensor a

Nissan Murano (Z52) 2015-2024 Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f10j / Dtc/circuit Diagnosis / P0706 Transmission Range Sensor a

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0706

T/M RANGE SENSOR A

(Transmission Range Sensor A Circuit Range/Performance) 		Diagnosis condition TCM power supply voltage: More than 11 V
Signal Transmission range switch signal
Threshold All range signals stay OFF
Diagnosis delay time Maintained for 30 seconds

POSSIBLE CAUSE

  • Harness or connector (Open circuit between ignition switch and transmission range switch/open circuit between transmission range switch and TCM)

  • Transmission range switch

  • Control cable

Harness or connector (CAN communication line is error)

FAIL-SAFE

  • Shift position indicator on combination meter is not displayed

  • Selector shock is large

  • Start is slow

  • Acceleration is slow

  • Lock-up is not performed

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for 40 seconds or more.)

  3. Check the first trip DTC.

Is “P0706” detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

ADJUSTMENT OF CONTROL CABLE

Adjust control cable. Refer to Inspection and Adjustment.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Select “Self Diagnostic Results” in “TRANSMISSION”.

  3. Touch “Erase”.

  4. Perform “DTC CONFIRMATION PROCEDURE". Refer to DTC Description.

Is “P0706” detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK POWER CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect transmission range switch connector.

  3. Turn ignition switch ON.

  4. Check voltage between transmission range switch harness connector terminal and ground.

    + − Voltage
    Transmission range switch
    Connector Terminal
    F29 4 Ground 10 – 16 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 7.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 1)

  1. Turn ignition switch OFF.

  2. Disconnect TCM connector.

  3. Check continuity between transmission range switch harness connector terminals and TCM harness connector terminals.

    Transmission range switch TCM Continuity
    Connector Terminal Connector Terminal
    F29 2 F25 4 Existed
    5 7
    8 6
    9 5

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace malfunctioning parts.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 2)

Check continuity between transmission range switch harness connector terminals and ground.

Transmission range switch — Continuity
Connector Terminal
F29 2 Ground Not existed
5
8
9

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace malfunctioning parts.

CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace transmission range switch. Refer to Removal and Installation.

DETECT MALFUNCTIONING ITEMS

Check the following items:

  • Harness open circuit or short circuit between ignition switch and IPDM E/R. Refer to Wiring Diagram - IGNITION POWER SUPPLY -.

  • Harness open circuit or short circuit between IPDM E/R connector terminal 64 and transmission range switch connector terminal 4.

  • 10A fuse (No. 45, located in the IPDM E/R). Refer to IPDM E/R Terminal Arrangement.

  • IPDM E/R

Is the check result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace malfunctioning parts.

Component Inspection

CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.

Transmission range switch Condition Continuity
Terminal
7 – 10 Manual lever: “P” and “N” positions Existed
Other than the above Not existed
4 – 5 Manual lever: “P” position Existed
Other than the above Not existed
4 – 8 Manual lever: “R” position Existed
Other than the above Not existed
4 – 9 Manual lever: “N position Existed
Other than the above Not existed
4 – 2 Manual lever: “D” position Existed
Other than the above Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

There is malfunction of transmission range switch. Replace transmission range switch. Refer to Removal and Installation.

    P0705 Transmission Range Sensor a

    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0705 T/M RANGE SENSOR A [Transmission Range Sensor A Circuit (PRNDL Input)] Diagnosis condition TCM power supply voltage: More than 11 V Signal Transmision range switch signal Threshold Two or more range signals simultaneously stay ON continuously Diagnosis delay time Maintained for 2 seconds POSSIBLE CAUSE Harness or connector (Short circuit between transmission range switch and TCM) Transmission range switch FAIL-SAFE Shift position indicator on combination meter is not displayed Selector shock is large Start is slow Acceleration is slow Lock-up is not performed DTC Confirmation Procedure PREPARATION BEFORE WORK If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test...

    P0711 Transmission Fluid Temperature Sensor a

    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0711 FLUID TEMP SENSOR A (Transmission Fluid Temperature Sensor A Circuit Range/Performance) 1 Diagnosis condition When all of the following conditions are satisfied...

    Other information:

    Nissan Murano (Z52) 2015-2024 Owners Manual: Climate controlled seat switches (if so equipped)


    The climate controlled seat warms up or cools down the front seat by blowingwarm or cool air from under the surface of the seat. The climate control switch is located on the center console. The climate controlled seat can be operated as follows: Place the ignition switch in the ON position...

    Nissan Murano (Z52) 2015-2024 Owners Manual: System maintenance


    The sensor for the ICC system is located on the front of the vehicle. To keep the ICC system operating properly, be sure to observe the following: Always keep the sensor area clean. Do not strike or damage the areas around the sensor. Do not attach a sticker (including transparent material) or install an accessory near the sensor...

    Categories

    Driver and passenger supplemental knee air bag

    Nissan Murano. Driver and passenger supplemental knee air bag

    Driver’s side

    The knee air bag is located in the knee bolster, on the driver’s and passenger’s side. All of the information, cautions and warnings in this manual apply and must be followed. The knee air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain collisions.

    Nissan Murano. Driver and passenger supplemental knee air bag

    Passenger’s side

    read more

     
    Copyright © 2025 www.nimurano.com