Nissan Murano: Basic Inspection / How to Erase Permanent Dtc

Nissan Murano (Z52) 2015-2024 Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f10j / Basic Inspection / How to Erase Permanent Dtc

Description

OUTLINE

Permanent DTC is erased with MIL shutoff if the same malfunction is not detected after performing the driving pattern for MIL shutoff three times.

PERMANENT DTC ITEM

For permanent DTC items, MIL turns ON. Refer to DTC Index.

HOW TO ERASE PERMANENT DTC

NOTE:

For permanent DTC group, refer to DTC Index.

CHECK DTC

Check DTC.

Is any DTC detected?

YES>>

Repair malfunction(s) and erase DTC.

NO>>

GO TO 2.

CHECK PERMANENT DTC

With CONSULT

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Turn ignition switch ON.

  5. Select “PERMANENT DTC STATUS” mode with CONSULT.

With GST

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Turn ignition switch ON.

  5. Select Service $0A with GST.

Is any permanent DTC detected?

YES>>

Permanent DTC group A: GO TO 3.

YES>>

Permanent DTC group B: GO TO 4.

YES>>

Permanent DTC group C: GO TO 5.

YES>>

Permanent DTC group D: GO TO 6.

YES>>

Permanent DTC group E: GO TO 7.

YES>>

Permanent DTC group F: GO TO 8.

NO>>

END

HOW TO ERASE PERMANENT DTC (GROUP A)

CAUTION:

Always drive at a safe speed.

Drive the Nissan Murano vehicle according to driving pattern D. Refer to Driving Pattern.

>>

GO TO 9.

HOW TO ERASE PERMANENT DTC (GROUP B)

CAUTION:

Always drive at a safe speed.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Start the engine.

  3. Stay P position over 10 seconds.

  4. Shift the selector lever to R position with brake pedal depressed and stay R position over 10 seconds.

  5. Shift the selector lever to N position with brake pedal depressed and stay N position over 10 seconds.

  6. Shift the selector lever to D position with brake pedal depressed and stay D position over 10 seconds.

  7. Drive the Nissan Murano vehicle according to driving pattern D. Refer to Driving Pattern.

>>

GO TO 9.

HOW TO ERASE PERMANENT DTC (GROUP C)

CAUTION:

Always drive at a safe speed.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Start the engine.

  3. Maintain the following conditions for 30 seconds or more.

    CAUTION:

    Always drive at a safe speed.

    Accelerator pedal position : 1.2/8
    Nissan Murano Vehicle speed : 60 km/h (38 MPH) or more

  4. Drive the vehicle according to driving pattern D. Refer to Driving Pattern.

>>

GO TO 9.

HOW TO ERASE PERMANENT DTC (GROUP D)

CAUTION:

Always drive at a safe speed.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Start the engine.

  3. Maintain the following conditions for 30 seconds or more.

    CAUTION:

    Always drive at a safe speed.

    Accelerator pedal position : 2.4/8
    Nissan Murano Vehicle speed : 80 km/h (50 MPH) or more

  4. Drive the vehicle according to driving pattern D. Refer to Driving Pattern.

>>

GO TO 9.

HOW TO ERASE PERMANENT DTC (GROUP E)

CAUTION:

Always drive at a safe speed.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Start the engine.

  3. Maintain the following conditions for 30 seconds or more.

    CAUTION:

    Always drive at a safe speed.

    Accelerator pedal position : 2.4/8
    Nissan Murano Vehicle speed : 80 km/h (50 MPH) or more

  4. Stop the vehicle.

  5. Fully depress accelerator pedal and accelerate by reaching 80 km/h (50 MPH) or more.

    CAUTION:

    Always drive at a safe speed.

  6. Drive the Nissan Murano vehicle according to driving pattern D. Refer to Driving Pattern.

>>

GO TO 9.

HOW TO ERASE PERMANENT DTC (GROUP F)

CAUTION:

Always drive at a safe speed.

  1. Adjust that fuel level is between 1/4 and 4/4.

  2. Move the Nissan Murano vehicle to a cool place.

    NOTE:

    Cool the vehicle in an environment of ambient air temperature less than 20°C (68°F).

  3. Turn ignition switch OFF and leave the Nissan Murano vehicle for 12 hours.

    CAUTION:

    Never turn ignition switch ON during this procedure.

    NOTE:

    The Nissan Murano vehicle must be cooled with the hood open.

  4. Start the engine.

  5. Shift the selector lever to N position and let engine idle for 5 minutes or more.

  6. Drive the Nissan Murano vehicle according to driving pattern D. Refer to Driving Pattern.

>>

GO TO 9.

CHECK PERMANENT DTC

With CONSULT

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Turn ignition switch ON.

  5. Select “PERMANENT DTC STATUS” mode with CONSULT.

With GST

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Turn ignition switch ON.

  5. Select Service $0A with GST.

Is any permanent DTC detected?

YES>>

GO TO 1.

NO>>

END

    Cvt Position

    Inspection and Adjustment INSPECTIONTurn ON the ignition switch with the shift selector at the “P” position. Press the shift selector button with the brake pedal depressed, and confirm that the shift selector can be moved to positions other than “P”...

    Dtc/circuit Diagnosis

    ..

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: B2796 Fr Sw Comm Error


    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2796 FR SW COMM ERROR (Front switch communication error) Diagnosis condition When ignition switch is ON. Signal (terminal) - Threshold - Diagnosis delay time 2 seconds or more POSSIBLE CAUSE A/C switch assembly A/C auto amp...

    Nissan Murano (Z52) 2015-2024 Service Manual: C1143 St Ang Sen Circuit


    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1143 ST ANG SEN CIRCUIT (Steering angle sensor circuit) Diagnosis condition When ignition switch ON. Signal (terminal) Steering angle sensor signal Threshold Steering angle sensor signal failure Diagnosis delay time 2 seconds or more POSSIBLE CAUSE Harness or connectors Steering angle sensor Power steering control module FAIL-SAFECertain steering assist force DTC Confirmation Procedure PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place the ignition switch in the OFF position and wait at least 10 seconds before conducting the next test...

    Categories

    read more

     
    Copyright © 2026 www.nimurano.com