Nissan Murano: Dtc/circuit Diagnosis / P0894 Transmission Component Slipping

Nissan Murano (Z52) 2015-2024 Service Manual / Transmission & Driveline / Transaxle & Transmission :: Cvt: Re0f10j / Dtc/circuit Diagnosis / P0894 Transmission Component Slipping

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P0894	T/M COMPONENT SLIPPING (Transmission component slipping)	Diagnosis condition	Constant Nissan Murano vehicle speed on the flat road
		Signal	—
		Threshold	CVT gear ratio: 0.498 less than
		Diagnosis delay time	30 seconds

POSSIBLE CAUSE

Pulley
Chain belt

FAIL-SAFE

Not changed from normal driving

Confirmation Procedure

CAUTION:

Diagnosis Procedure must be performed before starting “DTC CONFIRMATION PROCEDURE”. Refer to Diagnosis Procedure.

Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.

PRECONDITIONIG

If “DTC CONFIRMATION PROCEDURE” is previously conducted, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.

GO TO 2.

CHECK DTC DETECTION

Start the engine.
Drive the Nissan Murano vehicle at constant vehicle speed on the flat load for 30 seconds or more.
Check DTC

Is “P0894” detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE TRANSAXLE ASSEMBLY

Replace the transaxle assembly. Refer to Removal and Installation (front wheel drive) or Removal and Installation (all wheel drive).

YES>>

WORK END

P0890 Tcm

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0890 TCM (Transmission Control Module Power Relay Sense Circuit Low) Diagnosis condition TCM power supply voltage: More than 11 V Signal — Threshold Battery voltage: Less than 8...

P0965 Pressure Control Solenoid B

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0965 PC SOLENOID B (Pressure Control Solenoid B Control Circuit Range Performance) 1 Diagnosis condition When all of the following conditions are satisfied: DTC other than the applicable DTC is not detected...

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: Diagnosis and Repair Work Flow

Work Flow OVERALL SEQUENCEDETAILED FLOWINTERVIEW THE CUSTOMER FOR THE SYMPTOM Interview the customer for the symptom (the condition and the environment when the incident/malfunction occurs). >> GO TO 2. CHECK SYMPTOM Check the symptom from the customer information...

Nissan Murano (Z52) 2015-2024 Service Manual: B2416 Touch Sen R Open

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition B2416–1B TOUCH SEN R OPEN (Touch sensor right open) Diagnosis condition All times Signal (terminal) Touch sensor RH signal (automatic back door control module connector terminal: 4) Threshold When one of the following conditions is satisfied Touch sensor RH circuit is open Disconnect touch sensor RH connector Diagnosis delay time – B2416–1E TOUCH SEN R OPEN (Touch sensor right open) Diagnosis condition All times Signal (terminal) Touch sensor RH signal (automatic back door control module connector terminal: 4) Threshold When one of the following conditions is satisfied Touch sensor RH circuit is open Disconnect touch sensor RH connector Diagnosis delay time – POSSIBLE CAUSE Improper installation of touch sensor Touch sensor RH Harness or connectors (touch sensor circuit is open) Automatic back door control module FAIL-SAFEInhibit automatic back door system auto open/close function DTC Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Ignition switch ON...