Nissan Murano: Dtc/circuit Diagnosis / P2765 Input Speed Sensor B
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition | |
| P2765 |
INPUT SPEED SENSOR B (Input/Turbine Speed Sensor B Circuit) |
Diagnosis condition |
When all of the following conditions are satisfied:
|
| Signal | — | ||
| Threshold |
When all of the following conditions are satisfied:
|
||
| Diagnosis delay time | 5 seconds | ||
POSSIBLE CAUSE
-
Harness or connector (Output speed sensor circuit is open or shorted)
-
Output speed sensor
FAIL-SAFE
-
Start is slow
-
Acceleration is slow
-
Lock-up is not performed
-
Manual mode is not activated
CAUTION:
Be careful of the driving speed.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.
>>
GO TO 2.
CHECK DTC DETECTION
-
Start the engine.
-
Drive the Nissan Murano vehicle.
-
Maintain the following conditions for 10 seconds or more.
Selector lever : “D” position Engine speed : 1,200 rpm or more Nissan Murano Vehicle speed : 55 km/h (34 MPH) or more -
Stop the vehicle.
-
Check the first trip DTC.
Is “P2765” detected?
YES>>Go to Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
CHECK OUTPUT SPEED SENSOR POWER CIRCUIT
-
Turn ignition switch OFF.
-
Disconnect output speed sensor connector.
-
Turn ignition switch ON.
-
Check voltage between output speed sensor harness connector terminal and ground.
+ − Voltage Output speed sensor Connector Terminal F36 3 Ground 10 – 16 V
Is the inspection result normal?
YES>>GO TO 2.
NO>>GO TO 6.
CHECK OUTPUT SPEED SENSOR GROUND CIRCUIT
Check continuity between output speed sensor harness connector terminal and ground.
| Output speed sensor | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| F36 | 1 | Ground | Existed |
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace malfunctioning parts.
CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 1)
-
Turn ignition switch OFF.
-
Disconnect TCM connector.
-
Check continuity between output speed sensor harness connector terminal and TCM harness connector terminal.
Output speed sensor TCM Continuity Connector Terminal Connector Terminal F36 2 F25 34 Existed
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace malfunctioning parts.
CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 2)
Check continuity between output speed sensor harness connector terminal and ground.
| Output speed sensor | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| F36 | 2 | Ground | Not existed |
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace malfunctioning parts.
CHECK TCM INPUT SIGNALS
-
Connect all of disconnected connectors.
-
Lift the Nissan Murano vehicle.
-
Start the engine.
-
Check frequency of output speed sensor.
+ − Condition Frequency
(Approx.)TCM Connector Terminal F25 34 Ground -
Selector lever: “M1” position
-
Nissan Murano Vehicle speed: 20 km/h (12 MPH)
200 Hz
-
Is the inspection result normal?
YES>>Check intermittent incident. Refer to Intermittent Incident.
NO>>Replace output speed sensor. Refer to Removal and Installation.
DETECT MALFUNCTIONING ITEMS
Check the following items:
-
Harness open circuit or short circuit between ignition switch and IPDM E/R. Refer to Wiring Diagram - IGNITION POWER SUPPLY -.
-
Harness open circuit or short circuit between IPDM E/R connector terminal 61 and output speed sensor connector terminal 3.
-
10A fuse (No.43, located in the IPDM E/R). Refer to IPDM E/R Terminal Arrangement .
-
IPDM E/R
Is the check result normal?
YES>>Check intermittent incident. Refer to Intermittent Incident.
NO>>Repair or replace malfunctioning parts.
P2758 Tcc Pressure Control Solenoid
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P2758
TCC PRESSURE CONT SOLENOID
(Torque Converter Clutch Pressure Control Solenoid Control Circuit Stuck On)
Diagnosis condition
When all of the following conditions are satisfied:
TCM power supply voltage: More than 11 V
Lockup value learning is completed (After ignition switch ON)
Signal
—
Threshold
Coast capacity learning value: Less than –0...
P2813 Select Solenoid
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P2813
SELECT SOLENOID
(Select solenoid)
1
Diagnosis condition
When all of the following conditions are satisfied:
DTC other than the applicable DTC is not detected...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: On Board Refueling Vapor Recovery (orvr)
Component Function Check CHECK ORVR FUNCTION Check whether the following symptoms are present. Fuel odor from EVAP canister is strong. Cannot refuel/Fuel odor from the fuel filler opening is strong while refueling. Are any symptoms present? YES>> Proceed to Diagnosis Procedure...
Nissan Murano (Z52) 2015-2024 Service Manual: Main Power Window and Door Lock/unlock Switch
Removal and Installation REMOVAL Pull armrest in direction shown () then starting at rear release main power window and door lock/unlock switch finisher (1) pawls using a suitable tool (A). : Front : Pawl Disconnect the harness connectors (A) from the main power window and door lock/unlock switch (1) and harness connector (B) from the door mirror remote control switch (2) and remove...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- How to enable/disable the LDW system
- Memory storage function (key-link)
- High Beam Assist (if so equipped)
- New on site
- Most important about car
Vehicle security system
Your vehicle has two types of security systems:
Vehicle security system NISSAN Vehicle Immobilizer SystemThe vehicle security system provides visual and audible alarm signals if someone opens the doors, liftgate or the hood when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.
