Nissan Murano: Dtc/circuit Diagnosis / B1360 Combination Meter
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| B1360–02 |
Combination meter (Combination meter connection error) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
-
AV communication circuit is open
-
Combination meter
FAIL-SAFE
Steering switch is inoperative
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
Is DTC B1360 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT
Check combination meter power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace malfunctioning parts.
CHECK AV COMMUNICATION CIRCUIT
-
Ignition switch OFF.
-
Disconnect audio unit connector and combination meter connector.
-
Check the continuity between audio unit connector and combination meter connector.
Audio unit Combination meter Continuity Connector Terminal Connector Terminal M122 22 M23 50 Yes 23 42 49 43
Is the inspection result normal?
YES>>Replace combination meter. Refer to Removal and Installation.
NO>>Repair or replace malfunctioning parts.
B1341 Head Unit
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B1341–16
Head unit
(Audio unit)
[VB–LOW]
Diagnosis condition
When ignition switch is ON...
B1383 Incomp Steering Angle Sensor Adjust
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B1383–01
Incomp steering angle senor adjust
(Steering angle sensor calibration)
Diagnosis condition
When ignition switch is ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: System
System Description SYSTEM DIAGRAMAround View Monitor Control Unit Input Signal (CAN Communication)Transmit unitSignal name ABS actuator and electrical unit (Control unit) Wheel speed signal AV control unit Camera switch signal BCM Door switches state signal Combination meter Setting change request signal Hand brake switch signal IPDM E/R Battery voltage signal Sonar control unit Sonar detection display request signal Steering angle sensor Steering angle signal TCM Transmission range indication signal DESCRIPTION This system is equipped with wide-angle cameras on the front, rear and right and left door mirrors...
Nissan Murano (Z52) 2015-2024 Service Manual: System. Heated Steering Wheel System
System Description SYSTEM DIAGRAMINPUT/OUTPUT SIGNAL CHART Switch Input signal to A/C auto amp. A/C auto amp. function Actuator Heated steering wheel switch Switch ground signal Heated steering wheel control Heated steering wheel System DescriptionThe heated steering wheel switch controls the heated steering wheel relay through the A/C auto amp...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Rear bench seat adjustment
- All-Wheel Drive (AWD) (if so equipped)
- High Beam Assist (if so equipped)
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
