Nissan Murano: Dtc/circuit Diagnosis / U1304 Camera Image Calibration

U1302 Camera Power Volt

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1302 CAMERA POWER VOLT (Camera power voltage) Diagnosis condition When ignition switch is ON Signal (terminal) Camera power supply circuits Threshold Camera power supply voltage is 5...

Power Supply and Ground Circuit

Diagnosis Procedure CHECK FUSE Check that the following fuses are not blown: Terminal No. Signal name Fuse No. Capacity 40 Ignition signal 29 10 A Are the fuses blown? YES>> Replace the blown fuse after repairing the affected circuit...

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: P1611 Id Discord, Immu-Ecm

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition P1611 ID DISCORD, IMMU-ECM (Identification discord immobilizer-engine control unit) Diagnosis condition When ignition switch ON...

Nissan Murano (Z52) 2015-2024 Service Manual: P052a Intake Valve Timing Control

DTC Description DTC DETECTION LOGICThere is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P052A CAMSHAFT POSITION TIMING B1 (Cold start “A” camshaft position timing over-advanced bank 1) Diagnosis condition — Signal (terminal) — Threshold There is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions Diagnosis delay time — P052B CAMSHAFT POSITION TIMING B1 (Cold start “A” camshaft position timing over-retarded bank 1) Diagnosis condition — Signal (terminal) — Threshold There is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions Diagnosis delay time — P052C CAMSHAFT POSITION TIMING B2 (Cold start “A” camshaft position timing over-advanced bank 2) Diagnosis condition — Signal (terminal) — Threshold There is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions Diagnosis delay time — P052D CAMSHAFT POSITION TIMING B2 (Cold start “A” camshaft position timing over-retarded bank 2) Diagnosis condition — Signal (terminal) — Threshold There is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions Diagnosis delay time — POSSIBLE CAUSEDTC P052A Crankshaft position sensor Camshaft position sensor Intake valve timing control solenoid valve Intake valve timing intermediate lock control solenoid valve Accumulation of debris to the signal pick-up portion of the camshaft Timing chain installation Foreign matter caught in the intake valve timing control (or intermediate lock control) solenoid valve DTC P052B Crankshaft position sensor Camshaft position sensor Intake valve timing control solenoid valve Intake valve timing intermediate lock control solenoid valve Accumulation of debris to the signal pick-up portion of the camshaft Timing chain installation Foreign matter caught in the intake valve timing control (or intermediate lock control) solenoid valve DTC P052C Crankshaft position sensor Camshaft position sensor Intake valve timing control solenoid valve Intake valve timing intermediate lock control solenoid valve Accumulation of debris to the signal pick-up portion of the camshaft Timing chain installation Foreign matter caught in the intake valve timing control (or intermediate lock control) solenoid valve DTC P052D Crankshaft position sensor Camshaft position sensor Intake valve timing control solenoid valve Intake valve timing intermediate lock control solenoid valve Accumulation of debris to the signal pick-up portion of the camshaft Timing chain installation Foreign matter caught in the intake valve timing control (or intermediate lock control) solenoid valve FAIL-SAFE Engine operating condition in fail-safe mode Fail safe mode Nissan Murano Vehicle behavior Intake valve timing intermediate lock control — DTC Confirmation Procedure CHECK DTC PRIORITY If DTC P052A, P052B, P052C and P052D is displayed with DTC P0075 or P0081, first perform the confirmation procedure for DTC UXXXX or P0607...