Nissan Murano: Dtc/circuit Diagnosis / Steering Switches

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Information & Multimedia / Audio, Visual & Navigation System :: Navigation with Bose / Dtc/circuit Diagnosis / Steering Switches

Diagnosis Procedure

CHECK STEERING WHEEL AUDIO CONTROL SWITCH RESISTANCE

  1. Ignition switch OFF.

  2. Disconnect combination switch connector.

  3. Check resistance between the terminals of combination switch connector.

Combination switch Condition

Resistance (Ω)

(Approx.)
Connector Terminal Terminal
M143 31 33 Depress SOURCE switch. 1
Depress switch. 121
Depress switch. 321
Depress switch. 723
Depress OK switch. 2023
32 Depress switch. 1
Depress switch. 121
Depress switch. 321
Depress switch. 723
Depress switch. 2023

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace steering switches. Refer to Removal and Installation.

CHECK HARNESS BETWEEN COMBINATION METER AND COMBINATION SWITCH

  1. Disconnect combination meter connector and combination switch connector.

  2. Check continuity between combination meter connector and combination switch connector.

    Combination meter Combination switch Continuity
    Connector Terminal Connector Terminal
    M24 22 M41 4 Yes
    23 3
    21 2
  3. Check continuity between combination meter connector and ground.

    Combination meter Ground Continuity
    Connector Terminal
    M24 22 No
    23
    21

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connectors.

CHECK COMBINATION SWITCH

Check continuity between combination switch connector.

Combination switch Continuity
Connector Terminal Connector Terminal
M143 31 M41 4 Yes
32 3
33 2

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace spiral cable. Refer to Removal and Installation.

CHECK HARNESS BETWEEN COMBINATION METER AND AV CONTROL UNIT

  1. Disconnect combination meter connector and AV control unit connector.

  2. Check continuity between combination meter connector and AV control unit connector.

    Combination meter AV control unit Continuity
    Connector Terminal Connector Terminal
    M23 49 M162 22 Yes
    23
    50 42
    43
  3. Check continuity between combination meter connector and ground.

    Combination meter Ground Continuity
    Connector Terminal
    M23 49 No
    50

Is the inspection result normal?

YES>>

Replace AV Control unit. Refer to Removal and Installation.

NO>>

Repair or replace harness or connectors.

    Amp on Signal Circuit

    Diagnosis Procedure CHECK CONTINUITY BETWEEN AV CONTROL UNIT AND BOSE SPEAKER AMP. Ignition switch OFF. Disconnect AV control unit connector and Bose speaker amp...

    Front Auxiliary Input Jacks

    Diagnosis Procedure AUX JACKCHECK AUX JACK HARNESS CONTINUITY Ignition switch OFF. Disconnect AV control unit connector and front auxiliary input jacks connector...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: B2196 Dongle Ng


    DTC Description BCM performs ID verification between BCM and dongle unit.When verification result is OK, BCM permits cranking.DTC DETECTION LOGICNOTE: If DTC B2196 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to DTC Description...

    Nissan Murano (Z52) 2015-2024 Owners Manual: Audible reminders


    Brake pad wear warning The disc brake pads have audible wear warnings. When a disc brake pad requires replacement, it makes a high pitched scraping sound when the vehicle is in motion, whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard...

    Categories

    LATCH (Lower Anchors and Tethers for CHildren) system

    Nissan Murano. LATCH (Lower Anchors and Tethers for CHildren) system

    LATCH system lower anchor locations - bench seat

    Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.

    read more

     
    Copyright © 2026 www.nimurano.com