Nissan Murano: Power Supply and Ground Circuit / Intake Door Motor
CHECK INTAKE MODE DOOR MOTOR POWER SUPPLY
-
Ignition switch ON.
-
Check voltage between intake mode door motor harness connector and ground.
+ − Voltage
(Approx.)Intake mode door motor Connector Terminal M153 1 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 2.
NO>>GO TO 4.
CHECK INTAKE MODE DOOR MOTOR GROUND CIRCUIT
-
Ignition switch OFF.
-
Disconnect intake mode door motor connector.
-
Check continuity between intake mode door motor harness connector and ground.
Intake mode door motor — Continuity Connector Terminal M153 2 Ground Yes
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair harness or connector.
CHECK INSTALLATION OF INTAKE MODE DOOR MOTOR
Check intake mode door motor is properly installed. Refer to Exploded View.
Is the inspection result normal?
YES>>Replace intake mode door motor. Refer to Removal and Installation.
NO>>Repair or replace malfunctioning part.
CHECK INTAKE MODE DOOR MOTOR POWER SUPPLY CIRCUIT
-
Ignition switch OFF.
-
Disconnect intake mode door motor connector and A/C auto amp. connector.
-
Check continuity between intake mode door motor harness connector and A/C auto amp. harness connector.
Intake mode door motor A/C auto amp. Continuity Connector Terminal Connector Terminal M153 1 M50 17 Yes
Is the inspection result normal?
YES>>Replace A/C auto amp. Refer to Removal and Installation.
NO>>Repair harness or connector.
Mode Door Motor
Diagnosis Procedure
CHECK MODE DOOR MOTOR POWER SUPPLY
Ignition switch ON.
Check voltage between mode door motor harness connector and ground.
+ −
Voltage
(Approx...
Door Motor
Diagnosis Procedure
CHECK EACH DOOR MOTOR POWER SUPPLY
Ignition switch ON.
Check voltage between intake door motor harness connector and ground.
+ −
Voltage
(Approx...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Brake Fluid
Drain and Refill CAUTION: Do not spill or splash brake fluid on painted surfaces. Brake fluid may damage paint. If brake fluid is splashed on painted areas, wash it away with water immediately. Prior to repair, turn the ignition switch OFF, disconnect the harness connector from the ABS actuator and electric unit (control unit) or negative battery terminal...
Nissan Murano (Z52) 2015-2024 Service Manual: C1a00-44 Control Unit
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition C1A00-44 CONTROL UNIT (Control unit) Diagnosis condition When engine is running Signal (terminal) — Threshold ADAS control unit internal malfunction Diagnosis delay time 1 second or less POSSIBLE CAUSEADAS control unitFAIL-SAFEThe following systems are canceled: Vehicle-to-vehicle distance control mode Conventional (fixed speed) cruise control mode Automatic Emergency Braking (AEB) with pedestrian detection Automatic Emergency Braking (AEB) Intelligent Forward Collision Warning (I-FCW) Lane Departure Warning (LDW) Intelligent Lane Intervention (I-LI) Blind Spot Warning (BSW) Rear Cross Traffic Alert (RCTA) Rear Automatic Braking (RAB) Traffic Sign Recognition (TSR) Intelligent Drive Alertness (I-DA) Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Start the engine...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Checking engine oil level
- System malfunction
- How to enable/disable the LDW system
- New on site
- Most important about car
Luggage hooks
When securing items using luggage hooks located on the back of the seat or side finisher do not apply a load over more than 6.5 lbs. (29 N) to a single hook.
The luggage hooks that are located on the floor should have loads less than 110 lbs. (490 N) to a single hook.
