Nissan Murano: Heater & Air Conditioning Control System :: Dtc/circuit Diagnosis / Door Motor
CHECK EACH DOOR MOTOR POWER SUPPLY
-
Ignition switch ON.
-
Check voltage between intake door motor harness connector and ground.
+ − Voltage
(Approx.)Intake door motor Connector Terminal M153 1 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 2.
NO>>GO TO 3.
CHECK EACH DOOR MOTOR GROUND CIRCUIT
-
Ignition switch OFF.
-
Disconnect intake door motor connector.
-
Check continuity between intake door motor harness connector and ground.
Intake door motor — Continuity Connector Terminal M153 2 Ground Yes
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair harness or connector.
CHECK EACH DOOR MOTOR POWER SUPPLY CIRCUIT FOR OPEN
-
Disconnect A/C auto amp. connector.
-
Check continuity between intake door motor harness connector and A/C auto amp. harness connector.
Intake door motor A/C auto amp. Continuity Connector Terminal Connector Terminal M153 1 M50 17 Yes
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair harness or connector.
CHECK EACH DOOR MOTOR POWER SUPPLY CIRCUIT FOR SHORT
-
Disconnect following connectors:
-
Air mix door motor LH
-
Air mix door motor RH
-
Mode door motor
-
-
Check continuity between intake door motor harness connector and ground.
| Intake door motor | — | Continuity | ||
|---|---|---|---|---|
| Connector | Terminal | |||
| M153 | 1 | Ground | No | |
Is the inspection result normal?
YES>>Replace A/C auto amp. Refer to Removal and Installation.
NO>>Repair harness or connector.
Intake Door Motor
Diagnosis Procedure
CHECK INTAKE MODE DOOR MOTOR POWER SUPPLY
Ignition switch ON.
Check voltage between intake mode door motor harness connector and ground...
Door Motor Communication Circuit
Diagnosis Procedure
NOTE:
If all of door motor DTCs are detected, check this circuit.
CHECK EACH DOOR MOTOR COMMUNICATION SIGNAL
Ignition switch ON.
Check output waveform between A/C auto amp...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: P0706 Transmission Range Sensor a
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0706 T/M RANGE SENSOR A (Transmission Range Sensor A Circuit Range/Performance) Diagnosis condition TCM power supply voltage: More than 11 V Signal Transmission range switch signal Threshold All range signals stay OFF Diagnosis delay time Maintained for 30 seconds POSSIBLE CAUSE Harness or connector (Open circuit between ignition switch and transmission range switch/open circuit between transmission range switch and TCM) Transmission range switch Control cable Harness or connector (CAN communication line is error)FAIL-SAFE Shift position indicator on combination meter is not displayed Selector shock is large Start is slow Acceleration is slow Lock-up is not performed DTC Confirmation Procedure PREPARATION BEFORE WORK If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test...
Nissan Murano (Z52) 2015-2024 Service Manual: Buzzer
CONSULT Function (BCM - BUZZER) ECU IDENTIFICATIONThe BCM part number is displayed.SELF DIAGNOSTIC RESULTRefer to DTC Index.DATA MONITOR Monitor Item [Unit] Description PUSH SW [On/Off] Indicates condition of push-button ignition switch. UNLK SEN -DR [On/Off] Indicates condition of door unlock sensor...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Checking engine oil level
- Rear bench seat adjustment
- Settings
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
