Nissan Murano: Diagnosis System (bcm) / Int Lamp

Nissan Murano (Z52) 2015-2024 Service Manual / Electrical & Power Control / Body Control System :: Bcm / System Description / Diagnosis System (bcm) / Int Lamp

CONSULT Function (BCM - INT LAMP)

ECU IDENTIFICATION

The BCM part number is displayed.

SELF DIAGNOSTIC RESULT

Refer to DTC Index.

DATA MONITOR

Monitor Item [Unit]	Description
REQ SW -DR [On/Off]	Indicates condition of door request switch LH.
REQ SW -AS [On/Off]	Indicates condition of door request switch RH.
REQ SW -RR [On/Off]	Indicates condition of rear door request switch RH.
REQ SW -RL [On/Off]	Indicates condition of rear door request switch LH.
PUSH SW [On/Off]	Indicates condition of push-button ignition switch.
UNLK SEN -DR [On/Off]	Indicates condition of door unlock sensor.
DOOR SW-DR [On/Off]	Indicates condition of front door switch LH.
DOOR SW-AS [On/Off]	Indicates condition of front door switch RH.
DOOR SW-RR [On/Off]	Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off]	Indicates condition of rear door switch LH.
DOOR SW-BK [On/Off]	Indicates condition of back door switch.
CDL LOCK SW [On/Off]	Indicates condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW [On/Off]	Indicates condition of unlock signal from door lock and unlock switch.
KEY CYL LK-SW [On/Off]	Indicates condition of lock signal from door key cylinder switch.
KEY CYL UN-SW [On/Off]	Indicates condition of unlock signal from door key cylinder switch.
TRNK/HAT MNTR [On/Off]	Indicates condition of luggage room lamp switch.
RKE-LOCK [On/Off]	Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off]	Indicates condition of unlock signal from Intelligent Key.

ACTIVE TEST

Test Item	Description
INT LAMP	This test is able to check interior room lamp operation [On/Off].
STEP LAMP TEST	This test is able to check step lamp operation [On/Off].

WORK SUPPORT

NOTE:

The items listed below are the only applicable Work Support items for this Nissan Murano vehicle. If other items are displayed on CONSULT, do not use or change the setting for these other items.

Support Item	Setting	Description
SCENARIO LIGHTING SETTING	On	NOTE: Do not use this function since interior room lamp control is changed.
SCENARIO LIGHTING SETTING	Off*
FOG LAMP OVERRIDE	On*	Fog lamp override function ON.
FOG LAMP OVERRIDE	Off	Fog lamp override function OFF.

*: Initial setting

Buzzer

CONSULT Function (BCM - BUZZER) ECU IDENTIFICATIONThe BCM part number is displayed.SELF DIAGNOSTIC RESULTRefer to DTC Index.DATA MONITOR Monitor Item [Unit] Description PUSH SW [On/Off] Indicates condition of push-button ignition switch...

Head Lamp

CONSULT Function (BCM - HEAD LAMP) ECU IDENTIFICATIONThe BCM part number is displayed.SELF DIAGNOSTIC RESULTRefer to DTC Index.DATA MONITOR Monitor Item [Unit] Description PUSH SW [On/Off] Indicates condition of push-button ignition switch...

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: P0524 Engine Oil Pressure

DTC Description DTC DETECTION LOGICAn EOP sensor signal voltage applied to ECM remains lower than the specified value continuously for 10 seconds or more when the engine speed is 1,000 rpm or more. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0524 ENGINE OIL PRESSURE (Engine oil pressure too low) Diagnosis condition — Signal (terminal) Voltage signal transmitted from EOP sensor signal to ECM Threshold An EOP sensor signal voltage applied to ECM remains lower than the specified value continuously when the engine speed is 1,000 rpm or more Diagnosis delay time 10 seconds or more POSSIBLE CAUSE Decrease in engine oil pressure Decrease in engine oil level Engine oil condition EOP sensor Cause of engine oil consumption FAIL-SAFE Engine operating condition in fail-safe mode Fail safe mode Nissan Murano Vehicle behavior Engine oil pressure ECM illuminates oil pressure warning lamp on the combination meter...

Nissan Murano (Z52) 2015-2024 Service Manual: P0826 up and Down Shift Sw

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0826 UP/DOWN SHIFT SWITCH (Up and Down Shift Switch Circuit) Diagnosis condition Engine is started Signal — Threshold TCM monitors manual mode, non-manual mode, up or down switch signal, and detects as irregular when impossible input pattern occurs Diagnosis delay time 1 second or more POSSIBLE CAUSE Manual mode switch Harness or connectors (Manual mode switch circuit are open or shorted...