Nissan Murano: Dtc/circuit Diagnosis / B1383 Incomp Steering Angle Sensor Adjust

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Information & Multimedia / Audio, Visual & Navigation System :: Navigation with Bose / Dtc/circuit Diagnosis / B1383 Incomp Steering Angle Sensor Adjust

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B1383–01

Incomp steering angle senor adjust

(Steering angle sensor calibration)
Diagnosis condition When ignition switch is ON.
Signal (terminal)
Threshold
Diagnosis delay time

POSSIBLE CAUSE

  • Neutral position adjustment of the steering angle sensor is incomplete

  • Steering angle sensor

FAIL-SAFE

Predictive course line is not displayed

Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “MULTI AV”.

  5. Check DTC.

Is DTC B1383 detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

ADJUST NEUTRAL POSITION OF STEERING ANGLE SENSOR

Adjusts the steering angle sensor neutral position on ABS actuator and electrical unit (control unit) side. Refer to Work Procedure.

NOTE:

When B1383 is detected, adjust the predictive course line center position of the steering angle sensor.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

Perform DTC confirmation procedure again. Refer to DTC Confirmation Procedure.

Is DTC B1383 detected again?

YES>>

Replace steering angle sensor. Refer to Removal and Installation.

NO>>

Inspection End.

    B1360 Combination Meter

    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B1360–02 Combination meter (Combination meter connection error) Diagnosis condition When ignition switch is ON...

    B13cf Buttons

    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B13CF-73 Buttons (AV control unit) Diagnosis condition When ignition switch is ON...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: I-Li


    System Description SYSTEM DIAGRAMADAS CONTROL UNIT INPUT/OUTPUT SIGNAL ITEMInput Signal Item Transmit unit Signal name Description ECM CAN communication Brake pedal position switch signal Receives Brake pedal position switch state Accelerator pedal position signal Receives accelerator pedal position (angle) Stop lamp switch signal Receives stop lamp switch state Engine speed signal Receives engine speed TCM CAN communication Input speed signal Receives the number of revolutions of input shaft Current gear position signal Receives a current gear position Shift position signal Receives a selector lever position Output shaft revolution signal Receives the number of revolutions of output shaft ABS actuator and electric unit (control unit) CAN communication ABS malfunction signal Receives a malfunction state of ABS ABS operation signal Receives an operational state of ABS TCS malfunction signal Receives a malfunction state of TCS TCS operation signal Receives an operational state of TCS VDC OFF switch signal Receives an ON/OFF state of VDC VDC malfunction signal Receives a malfunction state of VDC VDC operation signal Receives an operational state of VDC Nissan Murano Vehicle speed signal (ABS) Receives wheel speeds of four wheels Yaw rate signal Receives yaw rate acting on the Nissan Murano vehicle Side G sensor signal Receives lateral G acting on the Nissan Murano vehicle Combination meter CAN communication Parking brake switch signal Receives an operational state of the parking brake System selection signal Receives a selection state of each item in "Driver Assistance" BCM CAN communication Turn indicator signal Receives an operational state of the turn signal lamp and the hazard lamp Steering angle sensor CAN communication Steering angle sensor malfunction signal Receives a malfunction state of steering angle sensor Steering angle sensor signal Receives the number of revolutions, turning direction of the steering wheel Steering angle speed signal Receives the turning angle speed of the steering wheel Lane intervention switch Lane intervention switch signal Receives an ON/OFF state of the lane intervention switch Lane camera unit ITS communication Detected lane condition signal Receives detection results of lane marker Output Signal Item Reception unit Signal name Description ABS actuator and electric unit (control unit) CAN communication Target yaw moment signal Transmits a target yaw moment signal to generate yaw moment to the Nissan Murano vehicle Combination meter CAN communication Intelligent Lane Intervention ON indicator lamp signal Transmits an Intelligent Lane Intervention ON indicator lamp signal to turn ON the Intelligent Lane Intervention ON indicator lamp Lane departure warning lamp signal Transmits an lane departure warning lamp signal to turn ON the lane departure warning lamp Lane camera unit ITS communication Nissan Murano Vehicle speed signal Transmits a vehicle speed calculated by the ADAS control unit Turn indicator signal Transmits a turn indicator signal received from BCM Steering assist system ON indicator Steering assist system ON indicator signal Turns ON the steering assist system ON indicator Intelligent Lane Intervention system ON indicator Intelligent Lane Intervention system ON indicator signal Turns ON the Intelligent Lane Intervention system ON indicator Warning system buzzer Warning buzzer signal Activates warning system buzzer...

    Nissan Murano (Z52) 2015-2024 Owners Manual: Checking lights


    With all doors closed, apply the parking brake, fasten the seat belts and place the ignition switch in the ON position without starting the engine. The following lights (if so equipped) will come on: , or , , , , The following lights (if so equipped) come on briefly and then go off: or , , , , If any light fails to come on or operate in a way other than described, it may indicate a burned-out bulb and/or a system malfunction...

    Categories

    Autolight system

    Nissan Murano. Autolight system

    The autolight system allows the headlights to turn on and off automatically. The autolight system can:

    Turn on the headlights, front parking, tail, license plate and instrument panel lights automatically when it is dark. Turn off all the lights (except daylight running lights) when it is light. Keep all the lights on for a period of time after you place the ignition switch in the OFF position and all doors are closed.

    read more

     
    Copyright © 2026 www.nimurano.com