Nissan Murano: Dtc/circuit Diagnosis / B1360 Combination Meter
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| B1360–02 |
Combination meter (Combination meter connection error) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
-
AV communication circuit is open
-
Combination meter
FAIL-SAFE
Steering switch is inoperative
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
Is DTC B1360 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT
Check combination meter power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace malfunctioning parts.
CHECK AV COMMUNICATION CIRCUIT
-
Ignition switch OFF.
-
Disconnect AV control unit connector and combination meter connector.
-
Check the continuity between AV control unit connector and combination meter connector.
AV control unit Combination meter Continuity Connector Terminal Connector Terminal M162 22 M23 49 Yes 23 42 50 43
Is the inspection result normal?
YES>>Replace combination meter. Refer to Removal and Installation.
NO>>Repair or replace malfunctioning parts.
B1346 Gps Antenna Connection
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B1346–13
GPS antenna connection
(GPS antenna connection)
[OPEN]
Diagnosis condition
When ignition switch is ON...
B1383 Incomp Steering Angle Sensor Adjust
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B1383–01
Incomp steering angle senor adjust
(Steering angle sensor calibration)
Diagnosis condition
When ignition switch is ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Door Switch
Component Function Check CHECK FUNCTION CONSULT Select “DOOR SW-DR”, “DOOR SW-AS”, “DOOR SW-RL” or “DOOR SW-RR” in “Data Monitor” mode of “BCM(DOOR LOCK)”. Check that the function operates normally according to the following conditions: Monitor Item Condition Status DOOR SW-DR Front door LH Open On Closed Off DOOR SW-AS Front door RH Open On Closed Off DOOR SW-RL Rear door LH Open On Closed Off DOOR SW-RR Rear door RH Open On Closed Off Is the inspection result normal? YES>> Door switch is OK...
Nissan Murano (Z52) 2015-2024 Service Manual: U1505-83 Side Rdr R Can Circ 2
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition U1505-83 SIDE RDR R CAN CIR 2 (Side radar right CAN circuit 2) Diagnosis condition When engine is running When Blind Spot Warning system is ON Signal (terminal) ITS communication signal Threshold ADAS control unit detects an error signal that is received from side radar RH via ITS communication Diagnosis delay time 1 second or less POSSIBLE CAUSE Side radar RH ADAS control unit FAIL- SAFEThe following systems are canceled: Blind Spot Warning (BSW) Rear Cross Traffic Alert (RCTA) Confirmation Procedure DTC CONFIRMATION PROCEDURECHECK DTC PRIORITY If DTC “U1505-83” is displayed with DTC “U1000–01” or “U1507-87”, first diagnose the DTC “U1000–01” or “U1507-87”...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Turning the AEB system on/off
- Settings
- Vehicle Dynamic Control (VDC) OFF switch
- New on site
- Most important about car
