Nissan Murano: Dtc/circuit Diagnosis / B1383 Incomp Steering Angle Sensor Adjust
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| B1383–01 |
Incomp steering angle senor adjust (Steering angle sensor calibration) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
-
Neutral position adjustment of the steering angle sensor is incomplete
-
Steering angle sensor
FAIL-SAFE
Predictive course line is not displayed
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
Is DTC B1383 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
ADJUST NEUTRAL POSITION OF STEERING ANGLE SENSOR
Adjusts the steering angle sensor neutral position on ABS actuator and electrical unit (control unit) side. Refer to Work Procedure.
NOTE:
When B1383 is detected, adjust the predictive course line center position of the steering angle sensor.
>>
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform DTC confirmation procedure again. Refer to DTC Confirmation Procedure.
Is DTC B1383 detected again?
YES>>Replace steering angle sensor. Refer to Removal and Installation.
NO>>Inspection End.
B1360 Combination Meter
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B1360–02
Combination meter
(Combination meter connection error)
Diagnosis condition
When ignition switch is ON...
B13cf Buttons
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B13CF-73
Buttons
(AV control unit)
Diagnosis condition
When ignition switch is ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Service After Replacing or Removing Engine Parts
Description SPECIAL REPAIR REQUIREMENT×: Applicable Part name Service performed Required service Reference Replacement Removal*1 ECM × Additional service when replacing ECM Description × Accelerator pedal released position learning Description Throttle valve closed position learning Description Idle air volume learning Description VIN registration Description Accelerator Pedal × × Accelerator pedal released position learning Work Procedure Electric throttle × × Throttle valve closed position learning Work Procedure × Idle air volume learning Work Procedure Engine assembly × Throttle valve closed position learning*2 Work Procedure Idle air volume learning*2 Work Procedure × Accelerator pedal released position learning Work Procedure Throttle valve closed position learning*2 Work Procedure *1: Harness connector disconnection included...
Nissan Murano (Z52) 2015-2024 Service Manual: Diagnosis and Repair Workflow
Work Flow OVERALL SEQUENCEDETAILED FLOWGET INFORMATION FOR SYMPTOM Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2. CONFIRM THE SYMPTOM Try to confirm the symptom described by the customer...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Tire rotation
- All-Wheel Drive (AWD) (if so equipped)
- Warning lights
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
