Nissan Murano: Dtc/circuit Diagnosis / B1360 Combination Meter
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| B1360–02 |
Combination meter (Combination meter connection error) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
-
AV communication circuit is open
-
Combination meter
FAIL-SAFE
Steering switch is inoperative
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
Is DTC B1360 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT
Check combination meter power supply and ground circuit. Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace malfunctioning parts.
CHECK AV COMMUNICATION CIRCUIT
-
Ignition switch OFF.
-
Disconnect AV control unit connector and combination meter connector.
-
Check the continuity between AV control unit connector and combination meter connector.
AV control unit Combination meter Continuity Connector Terminal Connector Terminal M162 22 M23 50 Yes 23 42 49 43
Is the inspection result normal?
YES>>Replace combination meter. Refer to Removal and Installation.
NO>>Repair or replace malfunctioning parts.
B1346 Gps Antenna Connection
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B1346–13
GPS antenna connection
(GPS antenna connection)
[OPEN]
Diagnosis condition
When ignition switch is ON...
B1383 Incomp Steering Angle Sensor Adjust
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B1383–01
Incomp steering angle senor adjust
(Steering angle sensor calibration)
Diagnosis condition
When ignition switch is ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: P01f0 Engine Coolant Temperature
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P01F0 00 Coolant temperature (Coolant temperature relapsed below diagnostic monitoring temperature) Diagnosis condition After engine warmed up Nissan Murano Vehicle speed is more than 60km/h (37 MPH) and no fuel cut Signal (terminal) Engine coolant temperature sensor signal Threshold When the engine coolant temperature is lower than threshold value, after Nissan Murano vehicle is driven at 60km/h (37 MPH) or more for certain period...
Nissan Murano (Z52) 2015-2024 Service Manual: Basic Inspection
Work Procedure INSPECTION START Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance. Open engine hood and check the following: Harness connectors for improper connections Wiring harness for improper connections, pinches and cut Vacuum hoses for splits, kinks and improper connections Hoses and ducts for leakage Air cleaner clogging Gasket Check that electrical or mechanical loads are not applied...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- GAS STATION INFORMATION
- Intelligent Forward Collision Warning (I-FCW)
- High Beam Assist (if so equipped)
- New on site
- Most important about car
Unfastening the seat belts. Checking seat belt operation
Unfastening the seat belts
To unfasten the seat belt, press the button
on the buckle 
. The seat belt
automatically
retracts.
