Nissan Murano: Dtc/circuit Diagnosis / Steering Switches
CHECK STEERING WHEEL AUDIO CONTROL SWITCH RESISTANCE
-
Ignition switch OFF.
-
Disconnect combination switch connector.
-
Check resistance between the terminals of combination switch connector.
| Combination switch | Condition |
Resistance Ω (Approx.) | ||
|---|---|---|---|---|
| Connector | Terminal | Terminal | ||
| M143 | 31 | 33 | Depress SOURCE switch. | 1 |
Depress  switch. |
121 | |||
Depress  switch. |
321 | |||
Depress  switch. |
723 | |||
| Depress OK switch. | 2023 | |||
| 32 | Depress   switch. |
1 | ||
Depress  switch. |
121 | |||
Depress  switch. |
321 | |||
Depress  switch. |
723 | |||
Depress  switch. |
2023 | |||
Is the inspection result normal?
YES>>GO TO 2.
NO>>Replace steering switches. Refer to Removal and Installation.
CHECK HARNESS BETWEEN COMBINATION METER AND COMBINATION SWITCH
-
Disconnect combination meter connector and combination switch connector.
-
Check continuity between combination meter connector and combination switch connector.
Combination meter Combination switch Continuity Connector Terminal Connector Terminal M24 22 M41 4 Yes 23 3 21 2 -
Check continuity between combination meter connector and ground.
Combination meter Ground Continuity Connector Terminal M24 22 — No 23 21
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness or connectors.
CHECK COMBINATION SWITCH
Check continuity between combination switch connectors.
| Combination switch | Continuity | |||
|---|---|---|---|---|
| Connector | Terminal | Connector | Terminal | |
| M143 | 31 | M41 | 4 | Yes |
| 32 | 3 | |||
| 33 | 2 | |||
Is the inspection result normal?
YES>>GO TO 4.
NO>>Replace spiral cable. Refer to Removal and Installation.
CHECK HARNESS BETWEEN COMBINATION METER AND AV CONTROL UNIT
-
Disconnect combination meter connector and AV control unit connector.
-
Check continuity between combination meter connector and AV control unit connector.
Combination meter AV control unit Continuity Connector Terminal Connector Terminal M23 49 M162 22 Yes 23 50 42 43 -
Check continuity between combination meter connector and ground.
Combination meter Ground Continuity Connector Terminal M23 49 — No 50
Is the inspection result normal?
YES>>Replace audio unit. Refer to Removal and Installation.
NO>>Repair or replace harness or connectors.
Power Supply and Ground Circuit. Av Control Unit
Diagnosis Procedure
CHECK FUSE
Check that the following fuses are not blown:
Terminal No. Signal name Fuse No. Capacity
7
ACC power supply
7
10 A
17
Ignition power supply
29
10 A
19
Battery power supply
15
20 A
Are the fuses blown?
YES>>
Replace the blown fuse after repairing the affected circuit...
Front Auxiliary Input Jacks
Diagnosis Procedure
AUX JACKCHECK AUX JACK HARNESS CONTINUITY
Ignition switch OFF.
Disconnect AV control unit connector and front auxiliary input jacks connector...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: C1b52-17 Blind Spot Warning Indicator Open Circuit
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1B52-17 BSW/BSI IND OPEN CIR (Blind Spot Warning indicator open circuit) Diagnosis condition When ignition switch is ON. Signal (terminal) – Threshold Open circuit in Blind Spot Warning indicator circuit is detected Diagnosis delay time – POSSIBLE CAUSE Blind Spot Warning indicator RH circuit Blind Spot Warning indicator RH Side radar RH FAIL-SAFEThe following systems are canceled: Blind Spot Warning (BSW) Rear Cross Traffic Alert (RCTA) DTC Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Start the engine...
Nissan Murano (Z52) 2015-2024 Service Manual: Diagnosis System (air Bag)
Diagnosis Description CAUTION: Do not use electrical test equipment on any circuit related to the SRS unless instructed to do so in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harness connectors. Do not attempt to repair, splice or modify SRS wiring harnesses...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Settings
- All-Wheel Drive (AWD) (if so equipped)
- Intelligent Forward Collision Warning (I-FCW)
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
