Nissan Murano: Changing wheels and tires / Spare tire (TEMPORARY USE ONLY spare tire)
When replacing a wheel without the TPMS
such as the spare tire, the TPMS will not
function.
Observe the following precautions if the
TEMPORARY USE ONLY spare tire must be
used. Otherwise, your vehicle could be
damaged or involved in an accident:
WARNING
- The spare tire should be used for
emergency use only. It should be replaced
with the standard tire at the
first opportunity to avoid possible tire
or differential damage.
- Drive carefully while the TEMPORARY
USE ONLY spare tire is installed. Avoid
sharp turns and abrupt braking while
driving.
- Periodically check spare tire inflation
pressure. Always keep the pressure of
the TEMPORARY USE ONLY spare tire
at 420 kPa, 4.2 bar (60 psi).
- With the TEMPORARY USE ONLY spare
tire installed do not drive the vehicle
at speeds faster than 50 mph
(80 km/h).
- When driving on roads covered with
snow or ice, the TEMPORARY USE
ONLY spare tire should be used on the
rear wheels and the original tire used
on the front wheels (drive wheels).
- Tire tread of the TEMPORARY USE
ONLY spare tire will wear at a faster
rate than the standard tire. Replace
the spare tire as soon as the tread
wear indicators appear.
- Do not use the spare tire on other
vehicles.
- Do not use more than one spare tire at
the same time.
- Do not tow a trailer when the TEMPORARY
USE ONLY spare tire is installed.
CAUTION
- Do not use tire chains on a TEMPORARY
USE ONLY spare tire. Tire chains
will not fit properly and may cause
damage to the vehicle.
- Because the TEMPORARY USE ONLY
spare tire is smaller than the original
tire, ground clearance is reduced. To
avoid damage to the vehicle, do not
drive over obstacles. Also,do not drive
the vehicle through an automatic car
wash since itmay get caught.
Wash the wheels when washing the vehicle
to maintain their appearance.
Clean the inner side of the wheels when
the wheel is changed or the underside
of the vehicle is washed...
Other information:
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
B2720–60
CORNER SENSOR [RL]
(Rear sonar sensor LH outer)
—
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
Rear sonar sensor LH outer internal failure (reset error)
Diagnosis delay time
—
B2720–61
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
Rear sonar sensor LH outer internal failure (configuration error)
Diagnosis delay time
—
B2720–62
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
Rear sonar sensor LH outer internal failure (power supply error)
Diagnosis delay time
—
B2720–63
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
Rear sonar sensor LH outer internal failure (self diag result)
Diagnosis delay time
—
B2720–65
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
Rear sonar sensor LH outer internal failure (over temperature)
Diagnosis delay time
—
B2720–66
Diagnosis condition
When ignition switch is ON
Signal (terminal)
Rear sonar sensor LH outer signal (terminal 22)
Threshold
Rear sonar sensor LH outer signal circuit is open or short to ground
Diagnosis delay time
—
B2720–67
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
Rear sonar sensor LH outer internal failure (diag dump error)
Diagnosis delay time
—
B2720–68
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
Rear sonar sensor LH outer internal failure (resonator error)
Diagnosis delay time
—
B2720–83
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
Rear sonar sensor LH outer internal failure (CRC error)
Diagnosis delay time
—
B2720–92
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
Rear sonar sensor LH outer internal failure (membrane error)
Diagnosis delay time
—
POSSIBLE CAUSE
Harness or connectors
Rear sonar sensor LH outer
FAIL-SAFE
Obstacle detection of rear sonar sensor LH outer is stopped
Audible warning (sonar buzzer) of all sensors is stopped
Sonar buzzer sounds for 3 seconds
DTC Confirmation Procedure
DTC CONFIRMATION PROCEDURE
CONSULT
Ignition switch ON...
Fusible Link
A melted fusible link can be detected either by visual inspection or by feeling with a finger tip. If its condition is questionable, use circuit tester or test lamp. 1
: Fusible link
CAUTION:
If fusible link should melt, it is possible that critical circuit (power supply or large current carrying circuit) is shorted...
Contexto visto en
pronosticoshoy.futbol hoy