Nissan Murano: Driver Assistance System :: Adas Control Unit / Precaution. Precautions

Nissan Murano (Z52) 2015-2024 Service Manual / Cruise Control & Driver Assistance / Driver Assistance System :: Adas Control Unit / Precaution. Precautions

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collisions.

Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” sections of this Service Manual.

WARNING:

Always observe the following items for preventing accidental activation:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, it is recommended that all maintenance and repair be performed by an authorized NISSAN/INFINITI dealer.

Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see “SRS AIR BAG”.

Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation:

When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition/power switch ON or engine running, never use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.

When using air or electric power tools or hammers, always switch the ignition/power switch OFF, disconnect the 12V battery or batteries, and wait at least 3 minutes before performing any service.

Precautions For Harness Repair

ITS communication uses a twisted pair line. Be careful when repairing it.

Solder the repaired area and wrap tape around the soldered area.

NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
Bypass connection is never allowed at the repaired area.

NOTE:
Bypass connection may cause ITS communication error. The spliced wire becomes separated and the characteristics of twisted line are lost.

Driver Assistance System :: Adas Control Unit

System Description

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: P2100 Throttle Control Motor Relay

DTC Description DTC DETECTION LOGIC ECM detects that the voltage of power source for throttle control motor is excessively low. ECM detects that the throttle control motor relay is stuck ON. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2100 ETC MOT PWR-B1 (Throttle actuator “A” control motor circuit/open) Diagnosis condition Start engine and let it idle Signal (terminal) Throttle control motor circuit Threshold ECM detects that the voltage of power source for throttle control motor is excessively low Diagnosis delay time — P2103 ETC MOT PWR-B1 (Throttle actuator “A” control motor circuit high) Diagnosis condition Ignition switch ON Signal (terminal) Throttle control motor circuit Threshold ECM detects that the throttle control motor relay is stuck ON Diagnosis delay time — POSSIBLE CAUSEDTC P2100 Harness or connectors (Throttle control motor relay circuit is open) Throttle control motor relay DTC P2103 Harness or connectors (Throttle control motor relay circuit is shorted) Throttle control motor relay FAIL-SAFE Engine operating condition in fail-safe mode Fail safe mode Nissan Murano Vehicle behavior Throttle control motor relay ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx...

Nissan Murano (Z52) 2015-2024 Service Manual: B1305 Control Unit Internal Fault

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B1305–04 Control unit internal error (Audio unit internal fault) [—] Diagnosis condition When ignition switch is ON. Signal (terminal) – Threshold Internal fault Diagnosis delay time 30 seconds or more POSSIBLE CAUSEAudio unit internal faultFAIL-SAFEAudio unit internal error DTC Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Ignition switch ON...