Nissan Murano: Interior Lighting System :: Dtc/circuit Diagnosis / Push-Button Ignition Switch Illumination Circuit
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION
CONSULT
-
Ignition switch ON.
-
Select “ENGINE SW ILLUMI” in “Active Test” mode of “BCM(INTELLIGENT KEY)”.
-
While operating the test items, check that the push-button ignition switch illumination turns ON/OFF.
On : Push-button ignition switch illumination ON Off : Push-button ignition switch illumination OFF
Does the push-button ignition switch illumination turn ON/OFF?
YES>>Push-button ignition switch illumination circuit is normal.
NO>>Refer to Diagnosis Procedure.
Provides the power supply and the ground to control the push-button ignition switch illumination.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION
CONSULT
-
Ignition switch ON.
-
Select “ENGINE SW ILLUMI” in “Active Test” mode of “BCM(INTELLIGENT KEY)”.
-
While operating the test item, check voltage between push-button ignition switch connector.
| (+) | (-) | Test item |
Voltage (Approx.) |
|
| Push-button ignition switch | Ground | ENGINE SW ILLUMI | ||
| Connector | Terminal | |||
| M208 | 5 | ON | 5 V | |
| OFF | 0 V | |||
Is the inspection result normal?
YES>>GO TO 4.
NO>>GO TO 2.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OPEN CIRCUIT
-
Ignition switch OFF.
-
Disconnect BCM harness connector and the push-button ignition switch harness connector.
-
Check continuity between BCM harness connector and the push-button ignition switch harness connector.
| BCM | Push-button ignition switch | Continuity | ||
|---|---|---|---|---|
| Connector | Terminal | Connector | Terminal | |
| M19 | 48 | M208 | 5 | Yes |
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness or connectors.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
| BCM | — | Continuity | |
| Connector | Terminal | ||
| M19 | 48 | Ground | No |
Is the inspection result normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Repair or replace harness or connectors.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND CIRCUIT
-
Ignition switch OFF.
-
Disconnect push-button ignition switch harness connector.
-
Check continuity between push-button ignition switch harness connector and ground.
Push-button ignition switch — Continuity Connector Terminal M208 6 Ground Yes
Is the inspection result normal?
YES>>Replace push-button ignition switch. Refer to Removal and Installation.
NO>>GO TO 5.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND OPEN CIRCUIT
-
Disconnect BCM harness connector and push-button ignition switch harness connector.
-
Check continuity between BCM harness connector and push-button ignition switch harness connector.
Push-button ignition switch BCM Continuity Connector Terminal Connector Terminal M208 6 M80 107 Yes
Is the inspection result normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Repair or replace harness or connectors.
Map Lamp Circuit
Description
Controls the lamp (ground side) by PWM signal (duty) when the map lamp main switch is DOOR.
Component Function Check
CAUTION:
Check the following items first:
Battery saver output/power supply circuit
Front room/map lamp assembly
CHECK MAP LAMP CONTROL FUNCTION
CONSULT
Ignition switch ON...
Interior Lighting System :: Symptom Diagnosis. Interior Lighting System Symptoms
Symptom Table
NOTE:
Perform the “Self Diagnostic Result” with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Main Power Window and Door Lock/unlock Switch
Removal and Installation REMOVAL Pull armrest in direction shown () then starting at rear release main power window and door lock/unlock switch finisher (1) pawls using a suitable tool (A). : Front : Pawl Disconnect the harness connectors (A) from the main power window and door lock/unlock switch (1) and harness connector (B) from the door mirror remote control switch (2) and remove...
Nissan Murano (Z52) 2015-2024 Service Manual: Multi Av System
Symptom Table RELATED TO AUDIO Symptoms Check items Probable malfunction location The disk cannot be removed. AV control unit Malfunction in AV control unit. Refer to On Board Diagnosis Function. No sound comes out or the level of the sound is low...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Warning lights
- Turning the AEB system on/off
- Indicator lights
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
