Nissan Murano: Dtc/circuit Diagnosis / Power Supply and Ground Circuit
CHECK FUSE
Check that the following fuses are not blown:
| Terminal No. | Signal name | Fuse No. | Capacity |
|---|---|---|---|
| 40 | Ignition signal | 29 | 10 A |
Are the fuses blown?
YES>>Replace the blown fuse after repairing the affected circuit.
NO>>GO TO 2.
CHECK POWER SUPPLY CIRCUIT
-
Ignition switch OFF.
-
Disconnect around view monitor control unit connector.
-
Check voltage between around view monitor control unit connector and ground.
Around view monitor control unit Ground Condition Voltage
(Approx.)Connector Terminal M96 40 — Ignition switch: ON Battery voltage
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness or connectors.
CHECK GROUND CIRCUIT
-
Ignition switch OFF.
-
Check continuity between around view monitor control unit connector and ground.
Around view monitor control unit Ground Continuity Connector Terminal M96 39 — Yes
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness or connectors.
U1304 Camera Image Calibration
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
U1304
CAMERA IMAGE CALIB
(Camera image calibration)
Diagnosis condition
When ignition switch is ON
Signal (terminal)
—
Threshold
—
Diagnosis delay time
—
POSSIBLE CAUSECamera calibration is incomplete...
Symptom Diagnosis. Intelligent Around View Monitor System
Symptom Table
INTELLIGENT AROUND VIEW MONITOR SYSTEMNOTE:
Inspect the vehicle for a front license plate frame or cover. If there is a front license plate frame or cover, the front camera will see it and show it on the monitor...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: U0102 Lost Communication (transfer)
DTC Description DTC DETECTION LOGICWhen the ignition switch is ON, TCM is unable to receive the CAN communications signal from AWD control unit continuously for 2 seconds or more. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0102 LOST COMM (TRANSFER) (Lost Communication With Transfer Case Control Module) Diagnosis condition When the ignition switch is ON Signal CAN communication signal Threshold TCM is unable to receive the CAN communications signal from AWD control unit Diagnosis delay time Continuously for 2 seconds or more POSSIBLE CAUSE AWD control unit Harness or connector (CAN communication line is open or shorted) FAIL-SAFENot changed from normal driving DTC Confirmation Procedure PREPARATION BEFORE WORK If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test...
Nissan Murano (Z52) 2015-2024 Service Manual: Electric Controlled Coupling
Exploded View Stud bolt Connector bracket Reamer bolt Electric controlled coupling assembly Wave spring Drive pinion oil seal Drive pinion lock nut Pinion front bearing Gear carrier Collapsible spacer Drive pinion adjusting shim Pinion rear bearing Drive pinion Drive gear Differential case Side bearing Side bearing adjusting shim Side oil seal Rear cover Stud bolt Gasket Drain plug Filler plug Pinion mate thrust washer Pinion mate gear Side gear thrust washer Side gear Pinion mate shaft Lock pin Oil seal lip Screw hole : N·m (kg-m, in-lb) : N·m (kg-m, ft-lb) : Always replace after every disassembly...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- How to enable/disable the LDW system
- Tire rotation
- Rear bench seat adjustment
- New on site
- Most important about car
Driver and passenger supplemental knee air bag
Driver’s side
The knee air bag is located in the knee bolster, on the driver’s and passenger’s side. All of the information, cautions and warnings in this manual apply and must be followed. The knee air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain collisions.
Passenger’s side
