Nissan Murano: Transmission & Driveline / Front Axle :: Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting

Nissan Murano (Z52) 2015-2024 Service Manual / Transmission & Driveline / Front Axle :: Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting

NVH Troubleshooting Chart

Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.

Reference			—	Inspection	—	Exploded View	—	Inspection	NVH Troubleshooting Chart	Inspection	NVH Troubleshooting Chart	NVH Troubleshooting Chart	Inspection	NVH Troubleshooting Chart	NVH Troubleshooting Chart
Possible cause and SUSPECTED PARTS			Excessive joint angle	Joint sliding resistance	Imbalance	Improper installation, looseness	Parts interference	Wheel bearing damage	FRONT SUSPENSION	FRONT AXLE	TIRE	WHEEL	DRIVE SHAFT	BRAKE	STEERING
Symptom	DRIVE SHAFT	Noise	×	×	-	-	-	×	×	×	×	×	-	×	×
	DRIVE SHAFT	Shake	×	-	×	-	-	×	×	×	×	×	-	×	×
	FRONT AXLE	Noise	-	-	-	×	×	×	×		×	×	×	×	×
		Shake	-	-	-	×	×	×	×		×	×	×	×	×
		Vibration	-	-	-	×	×	×	×	-	×	-	×	-	×
		Shimmy	-	-	-	×	×	-	×	-	×	×	-	×	×
		Shudder	-	-	-	×		-	×	-	×	×	-	×	×
		Poor quality ride or handling	-	-	-	×	×	-	×	-	×	×	-	-	-

Inspect Front Axle for cracks or damage.

×: Applicable

Front Axle :: Preparation. Preparation

Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description KV40107300 (J-51751) Boot band crimping tool Installing boot band KV38107900 (J–52469–1) Differential side oil seal protector Installing drive shaft A: 32 mm (1...

Front Axle :: Periodic Maintenance

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: P00fe Evap Control System

DTC Description This diagnosis detects clogs in the EVAP line between fuel tank and EVAP canister purge volume control solenoid valve.ECM controls EVAP control system as below. ECM monitors EVAP line pressure change to diagnose if there is no clogging between EVAP canister and fuel tank...

Nissan Murano (Z52) 2015-2024 Service Manual: Door Does Not Lock/unlock and Engine Does Not Start (all I-Key/req Sw/push Sw)

Diagnosis Procedure All doors do not lock/unlock using door request switch or back door does not open using back door opener request switch, Intelligent Key, and engine does not start when ignition switch is pressed while carrying Intelligent Key.SYMPTOM TABLE (BOTH INTELLIGENT KEYS HAVE THE SAME SYMPTOMS) Door lock operation (remote keyless entry) Door lock operation (request switch) or back door open operation (opener switch of back door panel) Engine started with ignition switch operation (registered Intelligent Key is within the detection area of inside key antenna) Engine started with ignition switch operation (registered Intelligent Key placed next to ignition switch) NG NG No crank, No start OK CONDITIONS OF VEHICLE (OPERATING CONDITIONS)“ENGINE START BY I-KEY” setting in “Work support” mode of “BCM(INTELLIGENT KEY)” is ON...