Nissan Murano: Symptom Diagnosis / Exterior Lighting System Symptoms

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Controls / Exterior Lighting System :: Led Headlamp / Symptom Diagnosis / Exterior Lighting System Symptoms

Symptom Table

NOTE:

Perform the “Self Diagnostic Result” with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected.

Symptom Possible cause Inspection item
Headlamp (HI) is not turned ON One side

  • Fuse

  • Headlamp (HI) power supply circuit

  • Front combination lamp internal circuit

    • LED (headlamp high)

    • LED headlamp control module

    • Harness

  • IPDM E/R

Headlamp (HI) circuit

Refer to Component Function Check.
Both sides

Symptom diagnosis

“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”

Refer to Diagnosis Procedure.

High beam indicator lamp is not turned ON

[Headlamp (HI) is turned ON] 		Combination meter

  • Combination meter “Data Monitor” “HI-BEAM IND”

  • IPDM E/R “Active Test” “EXTERNAL LAMPS”
Headlamp (LO) is not turned ON One side

  • Fuse

  • Headlamp (LO) power supply circuit

  • Front combination lamp internal circuit

    • LED (headlamp low)

    • LED headlamp control module

    • Harness

  • IPDM E/R

Headlamp (LO) circuit

Refer to Component Function Check.
Both sides

Symptom diagnosis

“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”

Refer to Diagnosis Procedure.
Headlamp (HI) and (LO) is not turned ON

  • LED headlamp ground circuit

  • Front combination lamp internal circuit

    • LED headlamp control module

    • Harness

LED headlamp

Refer to Diagnosis Procedure.
Each lamp is not turned ON/OFF with lighting switch AUTO

  • Combination switch input/output signal circuit

  • Combination switch

  • BCM

Combination switch

Refer to Symptom Table.

  • Optical sensor power supply/ground/signal circuit

  • Optical sensor

  • BCM

Optical sensor circuit

Refer to Component Function Check.
Parking lamp is not turned ON

  • Fuse

  • Parking lamp power supply/ground circuit

  • Front combination lamp internal circuit

    • LED (parking lamp)

    • Control circuit

    • Harness

  • IPDM E/R

Parking lamp circuit

Refer to Component Function Check.

Front side marker lamp is not turned ON

[Parking lamp is turned ON]

Front combination lamp internal circuit

  • Side marker lamp

  • Control circuit

  • Harness

Replace front combination lamp

Refer to Removal and Installation.
Tail lamp and rear side marker is not turned ON

  • Fuse

  • Tail lamp power supply/ground circuit

  • Rear combination lamp (body side) or rear combination lamp (back door side) internal circuit

    • LED (tail lamp)

    • LED (side marker lamp)

    • Harness

  • IPDM E/R

Tail lamp circuit

Refer to Component Function Check.

License plate lamp is not turned ON

[Tail lamp is turned ON]

  • License plate lamp power supply/ground circuit

  • License plate lamp bulb

  • License plate lamp bulb socket

  • IPDM E/R

License plate lamp circuit

Refer to Component Function Check.
Parking lamp, license plate lamp, side marker lamp and tail lamp are not turned ON

Symptom diagnosis

“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT TURNED ON”

Refer to Diagnosis Procedure.

Position lamp indicator is not turned ON

(Parking lamp, license plate lamp, side marker lamp and tail lamp are turned ON) 		Combination meter

  • Combination meter “Data Monitor” “LIGHT IND”

  • IPDM E/R “Active Test” “EXTERNAL LAMPS”
Daytime running light is not turned ON

  • Fuse

  • Daytime running light relay

  • Daytime running light relay power supply/control signal circuit

  • Daytime running light power supply/ground circuit

  • Front combination lamp internal circuit

    • LED (daytime running light)

    • Control circuit

    • Harness

  • IPDM E/R

  • BCM

Daytime running light circuit

Refer to Component Function Check.

  • ECM

  • Combination meter

  • BCM(HEAD LAMP) “Data Monitor” “ENGINE STATE”

  • Combination meter “Data Monitor” “PKB SW”
Back-up lamp is not turned ON

  • Back-up lamp power supply/ground circuit

  • Rear combination lamp (back door side) internal circuit

    • Back-up lamp

    • Harness

  • BCM

Back-up lamp circuit

Refer to Component Function Check.
  • Transmission range switch power supply/signal circuit

  • Transmission range switch

  • TCM

 TRANSMISSION “Data Monitor” “R POSITION SW”
Turn signal lamp does not blink

Indicator lamp is normal

(Applicable side performs high flasher activation)

  • Front turn signal lamp

    • Front turn signal lamp power supply/ground circuit

    • Front combination lamp

  • Side turn signal lamp

    • Side turn signal lamp power supply/ground circuit

    • Door mirror

  • Rear turn signal lamp

    • Rear turn signal lamp power supply/ground circuit

    • Rear combination lamp (body side)

Turn signal lamp circuit

Refer to Component Function Check.
Indicator lamp is included

  • Combination switch input/output signal circuit

  • Combination switch

  • BCM

Combination switch

Refer to Symptom Table.

Turn signal indicator lamp does not blink

(Turn signal lamp is normal) 		One side Combination meter —

Both sides

(Always)

  • Turn indicator signal

  • BCM

  • Combination meter

  • Combination meter “Data Monitor” “TURN IND”

  • BCM(FLASHER) “Active Test” “FLASHER”

Both sides

(Only when activating hazard warning lamp with ignition switch OFF)

  • Combination meter power supply/ground circuit

  • Combination meter

Combination meter

Power supply and ground circuit

Refer to Diagnosis Procedure.

  • Hazard warning lamp does not activate (Turn signal is normal)

  • Hazard warning lamp continues activating

  • Hazard switch signal/ground circuit

  • Hazard switch

  • BCM

Hazard switch circuit

Refer to Component Function Check.
Front fog lamp is not turned ON One side

  • Front fog lamp power supply/ground circuit

  • Front fog lamp

  • IPDM E/R

Front fog lamp circuit

Refer to Component Function Check.
Both sides

Symptom diagnosis

“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”

Refer to Diagnosis Procedure.

Front fog lamp indicator lamp is not turned ON

(Front fog lamp is turned ON) 		Combination meter

  • Combination meter “Data Monitor” “FR FOG IND”

  • BCM(HEAD LAMP) “Active Test” “FR FOG LAMP”
HBA is not turned ON/OFF

  • Combination switch input/output signal circuit

  • Combination switch

  • BCM

Combination switch

Refer to Symptom Table.

    Symptom Diagnosis

    ..

    Normal Operating Condition

    Description LED HEADLAMP LED brightness and color may slightly change until the temperature becomes stable. This is not a malfunction. Illumination time lag may occur between right and left...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: Sliding Sensor


    Component Function Check DATA MONITOR CONSULT Select “SLIDE PULSE” in “Data Monitor” mode of “AUTO DRIVE POS.”. Check that the function operates normally according to the following conditions: Monitor item Condition Value SLIDE PULSE Seat sliding Operate (forward) Change (decrease) Operate (backward) Change (increase) Release No change Is the inspection result normal? YES>> Inspection End...

    Nissan Murano (Z52) 2015-2024 Service Manual: Key Warning Lamp


    Component Function Check CHECK FUNCTION CONSULT Select “INDICATOR” in “Active Test” mode of “BCM(INTELLIGENT KEY)”. Select “KEY IND” or “KEY ON” to check that it works normally. Is the inspection result normal? YES>> Key warning lamp is OK...

    Categories

    Luggage hooks

    Nissan Murano. Luggage hooks

    When securing items using luggage hooks located on the back of the seat or side finisher do not apply a load over more than 6.5 lbs. (29 N) to a single hook.

    The luggage hooks that are located on the floor should have loads less than 110 lbs. (490 N) to a single hook.

    read more

     
    Copyright © 2026 www.nimurano.com