Nissan Murano: Instrument Panel :: Removal and Installation / Center Console Assembly

Nissan Murano (Z52) 2015-2024 Service Manual / Body Interior / Instrument Panel :: Removal and Installation / Center Console Assembly

Exploded View

1.	Center console side finisher (RH)	2.	Center console side finisher (LH)	3.	Center console lower side finisher (LH)
4.	Center console reinforcement bracket	5.	Mood lamp [front console LH (if equipped)]	6.	Mood lamp lens [front console LH (if equipped)]
7.	Center console upper side finisher (LH)	8.	Center console lid	9.	Mood lamp lens [rear console (if equipped)]
10.	Rear center ventilator duct	11.	Rear heated seat switch [LH (if equipped)]	12.	Center console rear finisher
13.	Rear USB charge port	14.	Rear ventilator grille assembly	15.	Rear heated seat switch [RH (if equipped)]
16.	Center console tray	17.	Center console rear tray mat	18.	Mood lamp [rear console RH (if equipped)]
19.	Mood lamp [rear console LH (if equipped)]	20.	Center console assembly	21.	Center console front tray mat
22.	Shift selector finisher	23.	Push-button ignition switch	24.	Front heated seat switch [RH (if equipped)]
25.	Front heated seat switch [LH (if equipped)]	26.	Front auxiliary input jacks	27.	Front power socket
28.	Front climate controlled seat switch [RH (if equipped)]	29.	Front climate controlled seat switch [LH (if equipped)]	30.	Center console upper side finisher (RH)
31.	Center console lower side finisher (RH)	32.	Mood lamp [front console RH (if equipped)]	33.	Mood lamp lens [front console RH (if equipped)]
	Metal clip		Clip		Pawl

Removal and Installation

REMOVAL

Release clips and pawls using a suitable tool and remove center console side finisher (LH/RH).

Release clips and remove center console upper side finisher (LH/RH).

Release clips and screws and remove center console lower side finisher (LH/RH).

Remove cluster lid C. Refer to Removal and Installation.

Remove shift selector knob. Refer to Exploded View.

Release clips using a suitable tool then disconnect harness connectors and remove shift selector finisher. Refer to Exploded View.

Remove center console rear tray mat. Refer to Exploded View.

Remove screw and release clips, then disconnect harness connectors from mood lamp [rear console RH/LH (if equipped)] and remove center console tray.

Remove screws (A) and release clips using a suitable tool then remove center console rear finisher (1).

: Metal clip

Remove center console screws (A).

Disconnect the remaining harness connectors and remove center console.

INSTALLATION

Installation is in the reverse order of removal.

Steering Column Covers

Removal and Installation REMOVALRemove steering column cover screws (A). NOTE: Rotate steering wheel to access steering column cover screws. Release steering column upper cover pawls using a suitable tool and remove...

Cluster Lid a

Removal and Installation REMOVALRemove instrument lower panel LH. Refer to Removal and Installation. Using a suitable tool, release pawls and remove gap hider (1) from steering column upper cover (2)...

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: Body Control System

System Description OUTLINE BCM controls various electrical components. It receives the information required from CAN communication and the signals received from each switch and sensor. BCM has a combination switch reading function for reading the status of combination switches (light, turn signal, wiper and washer) in addition to functions for controlling the operation of various electrical components...

Nissan Murano (Z52) 2015-2024 Service Manual: Additional Service When Replacing Distance Sensor (icc Sensor)

Description Always perform the radar alignment aiming adjustment after removing and installing or replacing the distance sensor (ICC sensor). CAUTION: The system does not operate normally unless the distance sensor (ICC sensor) is aligned properly. Perform the ICC system action test to check that the ICC system operates normally...