Nissan Murano: Steering Control System :: Dtc/circuit Diagnosis / C1606 Eps Motor
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| C1606 |
EPS MOTOR (EPS motor) |
Diagnosis condition | When engine is running. |
| Signal (terminal) | — | ||
| Threshold | Power steering motor failure or power steering control module motor driver failure | ||
| Diagnosis delay time | 1 second or more | ||
POSSIBLE CAUSE
-
Harness or connectors
-
Power steering control motor
-
Power steering control module
FAIL-SAFE
Manual steering state
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place the ignition switch in the OFF position and wait at least 10 seconds before conducting the next test.
>>
GO TO 2.
DTC REPRODUCTION PROCEDURE
CONSULT
-
Ignition switch OFF to ON.
-
Select "Self Diagnostic Result" mode of "EPS/DAST 3".
Is DTC “C1606” detected?
YES>>Proceed to diagnosis procedure. Refer to DTC Diagnosis Procedure.
NO>>Inspection End.
SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch OFF to ON.
-
Erase "Self Diagnostic Result" mode of "EPS/DAST 3".
-
Ignition switch OFF and wait for at least 10 seconds.
-
Ignition switch ON.
-
Select "Self Diagnostic Result" mode of "EPS/DAST 3".
Is DTC “C1606” detected?
YES>>Power steering motor is malfunctioning. Replace power steering oil pump assembly. Refer to Removal and Installation.
NO>>Check pin terminal and connection of each harness connector for malfunctioning conditions.
C1602 No Tuning Set
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition
C1602
NO TUNING SET
(No tuning set)
Diagnosis condition
When ignition switch ON...
C1609 Can Vhcl Speed
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition
C1609
CAN VHCL SPEED
(CAN Nissan Murano vehicle speed signal)
Diagnosis condition
When engine is ON
Signal (terminal)
Nissan Murano Vehicle speed signal
Threshold
ABS actuator and electric unit (control unit) input signal error is detected...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Motion Activated Back Door Control Unit
Reference Value TERMINAL LAYOUTPHYSICAL VALUES Terminal No. (Wire color) Description Condition Voltage (Approx.) (+) (–) Signal name Input/Output 1 (L) Ground Serial communication Input/Output — — 2 (V) Ground Power supply (BAT) Input — Battery voltage 3 (B) Ground Ground — — 0 V 4 (W) Ground Motion activated back door sensor (upper) input signal Input — — 5 (W) Ground Motion activated back door sensor (upper) output signal Input — — 6 (W) Ground Motion activated back door sensor (lower) input signal Input — — 7 (W) Ground Motion activated back door sensor (lower) output signal Input — — NOTE: Voltage generated in communication circuit between motion activated back door sensor and motion activated back door control unit is extremely low and therefore cannot be measured...
Nissan Murano (Z52) 2015-2024 Service Manual: Power Window and Door Lock/unlock Switch Rh
Reference Value TERMINAL LAYOUTPHYSICAL VALUES Terminal No. (wire color) Description Condition Voltage (Approx.) + - Signal name Input/Output 3 (Y/L) Ground Power window serial link Input/Output IGN SW ON or power window operating 4 (B) Ground Encoder ground — — — 5 (L/W) Ground Encoder power supply Output When ignition switch ON or power window timer operates...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Intelligent Forward Collision Warning (I-FCW)
- Rear bench seat adjustment
- How to enable/disable the LDW system
- New on site
- Most important about car
Luggage hooks
When securing items using luggage hooks located on the back of the seat or side finisher do not apply a load over more than 6.5 lbs. (29 N) to a single hook.
The luggage hooks that are located on the floor should have loads less than 110 lbs. (490 N) to a single hook.
