Nissan Murano: Door & Lock :: Dtc/circuit Diagnosis / B26fd Shft Lck Slnoid Insid F/b Mlfnc
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC Detection Condition | |
|---|---|---|---|
| B26FD |
SHFT LCK SLNOID INSID F/B MLFNC (Shift lock solenoid inside feedback malfunction) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | BCM terminals 108 | ||
| Threshold | BCM shift lock solenoid output control is OFF, but shift lock solenoid output feedback is ON | ||
| Diagnosis delay time | 1 second | ||
POSSIBLE CAUSE
-
Shift lock solenoid
-
Harness or connector
-
Shift lock solenoid circuit is open or shorted
-
Stop lamp switch
FAIL-SAFE
—
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of “BCM”.
Is DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO>>Shift lock solenoid is OK.
CHECK POWER SOURCE (STOP LAMP SWITCH)
-
Ignition switch OFF.
-
Disconnect stop lamp switch connector.
-
Check voltage between stop lamp switch connector and ground.
Stop lamp switch Ground Voltage
(Approx.)Connector Terminal E38 1 Battery voltage
Is the inspection result normal?
YES>>GO TO 2.
NO>>Check the following:
-
Harness for short or open between fuse block (J/B) and stop lamp switch
-
10A fuse (No. 10, located in fuse block [J/B])
CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Replace stop lamp switch. Refer to Exploded View.
CHECK GROUND CIRCUIT (BCM)
-
Disconnect BCM connector.
-
Check continuity between BCM connector and ground.
BCM Ground Continuity Connector Terminal M81 134 Yes 143
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace damaged parts.
CHECK HARNESS BETWEEN BCM AND STOP LAMP SWITCH FOR OPEN
Check continuity between BCM connector and stop lamp switch connector.
| BCM | Stop lamp switch | Continuity | ||
| Connector | Terminal | Connector | Terminal | |
| M18 | 27 | E38 | 2 | Yes |
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace damaged parts.
CHECK HARNESS BETWEEN BCM AND STOP LAMP SWITCH FOR SHORT CIRCUIT
Check continuity between BCM connector and ground.
| BCM | Ground | Continuity | |
| Connector | Terminal | ||
| M18 | 27 | No | |
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace damaged parts.
CHECK HARNESS BETWEEN BCM AND CVT SHIFT SELECTOR FOR OPEN
-
Disconnect CVT shift selector connector.
-
Check continuity between BCM and CVT shift selector.
BCM CVT shift selector Continuity Connector Terminal Connector Terminal M80 108 M78 3 Yes
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace damaged parts.
CHECK HARNESS BETWEEN BCM AND CVT SHIFT SELECTOR FOR SHORT CIRCUIT
Check continuity between BCM and ground.
| BCM | Ground | Continuity | |
| Connector | Terminal | ||
| M80 | 108 | No | |
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair or replace damaged parts.
CHECK GROUND CIRCUIT (CVT SHIFT SELECTOR)
Check continuity between CVT shift selector and ground.
| CVT shift selector | Ground | Continuity | |
| Connector | Terminal | ||
| M78 | 4 | Yes | |
Is the inspection result normal?
YES>>Replace shift lock solenoid. Refer to Exploded View.
NO>>Repair or replace damaged parts.
B2622 Inside Antenna
DTC Description
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information...
B26fe Hood Sw Can Diag Error
DTC Description
DTC DETECTION LOGICNOTE:
If DTC B26FE is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to DTC Description...
Other information:
Nissan Murano (Z52) 2015-2024 Owners Manual: Intelligent Cruise Control (ICC) (if so equipped)
CRUISE ON/OFF switch WARNING Failure to follow the warnings and instructions for proper use of the ICC system could result in serious injury or death. The ICC system is only an aid to assist the driver and is not a collision warning or avoidance device...
Nissan Murano (Z52) 2015-2024 Service Manual: System
System Description SYSTEM DIAGRAMDISTANCE SENSOR (ICC SENSOR) INPUT/OUTPUT SIGNAL ITEMInput Signal Item Transmit unit Signal name Description ADAS control unit ITS communication ADAS sensor signal State of ADAS Output Signal Item Reception unit Signal name Description ADAS control unit ITS communication Distance sensor (ICC sensor) signal Transmits information for ICC ADAS CONTROL UNIT INPUT/OUTPUT SIGNAL ITEMInput Signal Reception unit Signal name Description ECM CAN communication Engine speed signal Receives engine speed Accelerator pedal position signal Receives accelerator pedal position (angle) Closed throttle position signal Receives idle position state (ON/OFF) ICC prohibition signal Receives operable/inoperable state of the ICC system ICC steering switch signal Main switch signal Receives the operational state of the ICC steering switch SET/COAST switch signal CANCEL switch signal RESUME/ACCELERATE switch signal DISTANCE switch signal Stop lamp switch signal Receives an operational state of the brake pedal Brake pedal position switch signal Receives an operational state of the brake pedal TCM CAN communication Input speed signal Receives the number of revolutions of input shaft Output shaft revolution signal Receives the number of revolutions of output shaft Current gear position signal Receives a current gear position Shift position signal Receives a selector lever position ABS actuator and electric unit (control unit) CAN communication ABS malfunction signal Receives a malfunction state of ABS ABS operation signal Receives an operational state of ABS ABS warning lamp signal Receives an ON/OFF state of ABS warning lamp TCS malfunction signal Receives a malfunction state of TCS TCS operation signal Receives an operational state of TCS VDC OFF switch signal Receives an ON/OFF state of VDC VDC malfunction signal Receives an malfunction state of VDC VDC operation signal Receives an operational state of VDC Nissan Murano Vehicle speed signal (ABS) Receives wheel speeds of four wheels Stop lamp switch signal Receives an operational state of the brake pedal Yaw rate signal Receives yaw rate acting on Nissan Murano vehicle Combination meter CAN communication Parking brake switch signal Receives an operational state of the parking brake System selection signal Receives a selection state of AEB system Steering angle sensor CAN communication Steering angle sensor malfunction signal Receives a malfunction state of steering angle sensor Steering angle sensor signal Receives the number of revolutions and turning direction of the steering wheel Steering angle speed signal Receives the turning angle speed of the steering wheel Distance sensor (ICC sensor) ITS communication Distance sensor (ICC sensor) signal Receives detection information, such as the presence or absence of a leading Nissan Murano vehicle, and distance from the vehicle...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Checking engine oil level
- How to enable/disable the LDW system
- Settings
- New on site
- Most important about car
Luggage hooks
When securing items using luggage hooks located on the back of the seat or side finisher do not apply a load over more than 6.5 lbs. (29 N) to a single hook.
The luggage hooks that are located on the floor should have loads less than 110 lbs. (490 N) to a single hook.
