Nissan Murano: Srs Air Bag Control System :: Dtc/circuit Diagnosis / B1431 Seat Belt Pre-Tensioner

Nissan Murano (Z52) 2015-2024 Service Manual / Restraints / Srs Air Bag Control System :: Dtc/circuit Diagnosis / B1431 Seat Belt Pre-Tensioner

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B1431-1A

PRE-TEN FRONT RH

[SHORT]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Front RH seat belt pre-tensioner (shoulder belt) circuits are shorted to each other (terminals 19 and 20).
Threshold —
Diagnosis delay time —
B1431-13

PRE-TEN FRONT RH

[OPEN]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Front RH seat belt pre-tensioner (shoulder belt) circuit is open (terminals 19 and 20).
Threshold —
Diagnosis delay time —
B1431-12

PRE-TEN FRONT RH

[VB-SHORT]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Front RH seat belt pre-tensioner (shoulder belt) circuit is shorted to a power supply circuit (terminals 19 and 20).
Threshold —
Diagnosis delay time —
B1431-11

PRE-TEN FRONT RH

[GND-SHORT]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Front RH seat belt pre-tensioner (shoulder belt) circuit is shorted to ground (terminals 19 and 20).
Threshold —
Diagnosis delay time —
B1431-09

PRE-TEN FRONT RH

[SHORT]
Diagnosis condition When ignition switch is ON.
Signal (terminal) Front RH seat belt pre-tensioner (shoulder belt) circuits are shorted to each other (terminals 19 and 20).
Threshold —
Diagnosis delay time —

POSSIBLE CAUSE

[OPEN]

  • Connection malfunction or open circuit of harness and connector

  • Internal malfunction of front RH seat belt pre-tensioner (shoulder belt)

  • Internal malfunction of air bag diagnosis sensor unit

[VB-SHORT]

  • Connection malfunction or short circuit to power supply of harness and connector

  • Internal malfunction of front RH seat belt pre-tensioner (shoulder belt)

  • Internal malfunction of air bag diagnosis sensor unit

[GND-SHORT]

  • Connection malfunction or short circuit to ground of harness and connector

  • Internal malfunction of front RH seat belt pre-tensioner (shoulder belt)

  • Internal malfunction of air bag diagnosis sensor unit

[SHORT]

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of front RH seat belt pre-tensioner (shoulder belt)

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON.

  2. Select "Self Diagnostic Result" mode of "AIR BAG".

  3. Check for DTC.

Is the DTC detected?

YES>>

(Current DTC) Refer to DTC Diagnosis Procedure.

YES>>

(Past DTC) GO TO 2.

NO>>

Inspection End.

ERASE SELF DIAGNOSTIC RESULT

CONSULT

Erase the DTC.

Can the DTC be erased?

YES>>

Inspection End.

NO>>

Refer to DTC Diagnosis Procedure.

DTC CONFIRMATION PROCEDURE

CHECK SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON.

  2. Check the air bag warning lamp status. Refer to SRS Operation Check.

NOTE:

SRS will not enter diagnosis mode if no malfunction is detected in user mode.

Is the DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

WARNING:

  • Before servicing, ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

  • Never use unspecified tester or other measuring device.

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

    NOTE:

    All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors).

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform one of the following repairs:

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Select "Self Diagnostic Result" mode of "AIR BAG".

  4. Check for DTC.

Is DTC still current?

YES>>

GO TO 3.

NO>>

Refer to Intermittent Incident.

WIRING HARNESS

Check the wiring harness for visible damage.

NOTE:

The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors).

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace the harness.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Select "Self Diagnostic Result" mode of "AIR BAG".

  4. Check for DTC.

Is DTC still current?

YES>>

GO TO 5.

NO>>

Refer to Intermittent Incident.

FRONT RH SEAT BELT PRE-TENSIONER (SHOULDER BELT)

CONSULT

  1. Replace the front RH seat belt pre-tensioner (shoulder belt). Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Select "Self Diagnostic Result" mode of "AIR BAG".

  4. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Clear DTC. Inspection End.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Select "Self Diagnostic Result" mode of "AIR BAG".

  4. Check for DTC.

Is DTC still current?

YES>>

GO TO 7.

NO>>

Clear DTC. Inspection End.

RELATED HARNESS

Replace the related harness.

>>

Inspection End.

    B142x Collision Detection

    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition B1421-00 FRONTAL COLLISION Diagnosis condition When ignition switch is ON...

    Srs Air Bag Control System :: Symptom Diagnosis

    ..

    Other information:

    Nissan Murano (Z52) 2015-2024 Owners Manual: Answer back horn feature


    If desired, the answer back horn feature can be deactivated using the Intelligent Key. When it is deactivated and the button is pushed, the hazard indicator lights flash twice. When the button is pushed, neither the hazard indicator lights nor the horn operates...

    Nissan Murano (Z52) 2015-2024 Service Manual: Mood Lamp


    Removal and Installation FRONT CONSOLERemovalRemove center console upper side finisher. Refer to Exploded View. Remove mood lamp (front console) (1) screw (B). Release harness connector (A) clip using a suitable tool and disconnect the harness connector from the mood lamp (front console)...

    Categories

    Seatback pockets

    Nissan Murano. Seatback pockets

    Theremaybe one or two seatback pockets located on the back of the driver and passenger seats. The pockets can be used to store maps.

    WARNING

    read more

     
    Copyright © 2026 www.nimurano.com