Nissan Murano: Srs Air Bag Control System :: Dtc/circuit Diagnosis / B142x Collision Detection
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen items (Trouble diagnosis content) | DTC detecting condition | |
|---|---|---|---|
| B1421-00 | FRONTAL COLLISION | Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B1422-00 | SIDE COLLISION | Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B1423-00 | ROLLOVER DETECTION | Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B1425-00 | REAR COLLISION | Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
[B1421-00]
-
Malfunction of frontal-related parts
-
Internal malfunction of air bag diagnosis sensor unit
[B1422-00]
-
Malfunction of side-related parts
-
Internal malfunction of air bag diagnosis sensor unit
[B1423-00]
-
Malfunction of rollover-related parts
-
Internal malfunction of air bag diagnosis sensor unit
[B1425-00]
-
Malfunction of rear-related parts
-
Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
CHECK SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch ON.
-
Select "Self Diagnostic Result" mode of "AIR BAG".
-
Check for DTC.
Is the DTC detected?
YES>>(Current DTC) Refer to DTC Diagnosis Procedure.
YES>>(Past DTC) GO TO 2.
NO>>Inspection End.
ERASE SELF DIAGNOSTIC RESULT
CONSULT
Erase the DTC.
Can the DTC be erased?
YES>>Inspection End.
NO>>Refer to DTC Diagnosis Procedure.
DTC CONFIRMATION PROCEDURE
CHECK SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch ON.
-
Check the air bag warning lamp status. Refer to SRS Operation Check.
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO>>Inspection End.
Refer to For Frontal Collision or For Side and Rollover Collision.
B1427 Config Setting
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen items
(Trouble diagnosis content) DTC Detection Condition
B1427-55
ECU SETTING
(Electronic control unit setting)
Diagnosis condition
When ignition switch is ON...
B1431 Seat Belt Pre-Tensioner
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen items
(Trouble diagnosis content) DTC detecting condition
B1431-1A
PRE-TEN FRONT RH
[SHORT]
Diagnosis condition
When ignition switch is ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Normal Operating Condition
Description Symptom Result Brake pedal slightly vibrates and operation sound (motor sound and sound from suspension) occurs when VDC function, TCS function, ABS function, EBD function, brake assist function, hill start assist function operates. This is not a malfunction, because it is caused by VDC function, TCS function, ABS function, EBD function, brake assist function, hill start assist function that are normally operated...
Nissan Murano (Z52) 2015-2024 Service Manual: P0222 Tp Sensor
DTC Description DTC DETECTION LOGIC An excessively low voltage from the TP sensor 1 is sent to ECM. An excessively high voltage from the TP sensor 1 is sent to ECM. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0222 TP SEN 1/CIRC-B1 (Throttle/Pedal position sensor/switch “B” circuit low) Diagnosis condition Start engine and let it idle Signal (terminal) Voltage signal transmitted from TP sensor 1 to ECM Threshold An excessively low voltage from the TP sensor 1 is sent to ECM Diagnosis delay time — P0223 TP SEN 1/CIRC-B1 (Throttle/Pedal position sensor/switch “B” circuit high) Diagnosis condition Start engine and let it idle Signal (terminal) Voltage signal transmitted from TP sensor 1 to ECM Threshold An excessively high voltage from the TP sensor 1 is sent to ECM Diagnosis delay time — POSSIBLE CAUSEP0222 Harness or connectors (TP sensor 1 circuit is open or shorted...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- GAS STATION INFORMATION
- System malfunction
- Jacking up vehicle and removing the damaged tire
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
