Nissan Murano: Dtc/circuit Diagnosis / B1328 External Microphone 1
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| B1328–13 |
External Microphone 1 (Microphone) |
[OPEN] | Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | |||
| Threshold | – | |||
| Diagnosis delay time | 30 seconds or more | |||
| B1328–11 | [GND–SHORT] | Diagnosis condition | When ignition switch is ON. | |
| Signal (terminal) | — | |||
| Threshold | – | |||
| Diagnosis delay time | 30 seconds or more | |||
| B1328–12 | [VB–SHOR] | Diagnosis condition | When ignition switch is ON. | |
| Signal (terminal) | — | |||
| Threshold | – | |||
| Diagnosis delay time | 30 seconds or more | |||
POSSIBLE CAUSE
-
Microphone is not connected
-
Harness or connector
FAIL-SAFE
Microphone is inoperative
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
Is DTC B1328 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
DETERMINE MALFUNCTION TYPE
CONSULT
-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
Is DTC B1328–11, 12 or 13 detected?
YES>>13 [OPEN] or 11 [GND–SHORT] – GO TO 2.
YES>>12 [VB–SHOR] – GO TO 3.
NO>>Refer to Intermittent Incident.
CHECK MICROPHONE CIRCUITS FOR OPEN
-
Ignition switch OFF.
-
Disconnect AV control unit connector and microphone connector.
-
Check the continuity between AV control unit connector and microphone connector.
AV control unit Microphone Continuity Connector Terminal Connector Terminal M162 39 R8 4 Yes 40 1 51 5 59 2 -
Check the continuity between AV control unit connector and ground.
AV control unit Ground Continuity Connector Terminal M162 39 — No 40 51
Is the inspection result normal?
YES>>Replace microphone. Refer to Removal and Installation.
NO>>Repair or replace harness or connectors.
CHECK MICROPHONE CIRCUITS FOR SHORT TO POWER SUPPLY
-
Ignition switch ON.
-
Check the voltage between AV control unit connector and ground.
AV control unit Ground Voltage
(Approx.)Connector Terminal M162 39 — 0 V 40 51 59
Is the inspection result normal?
YES>>Replace microphone. Refer to Removal and Installation.
NO>>Repair or replace harness or connectors.
B1315 Am/fm 1 Antenna
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B1315–13
AM/FM 1 antenna
(Radio antenna)
[OPEN]
Diagnosis condition
When ignition switch is ON...
B132a External Usb
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B132A–13
External USB
(USB)
[OPEN]
Diagnosis condition
When ignition switch is ON...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Steering Gear and Linkage
Inspection BOOTCheck boot for cracks. Replace if any damage is found.OUTER SOCKET AND INNER SOCKET Ball joint swinging torque Hook the Tool at the measuring point and pull the Tool. Make sure that the Tool reads the specified value when ball stud and inner socket start to move...
Nissan Murano (Z52) 2015-2024 Service Manual: Rab
System Description SYSTEM DIAGRAMADAS CONTROL UNIT INPUT/OUTPUT SIGNAL ITEMInput Signal Item Transmit unit Signal name Description ECM CAN communication Closed throttle position signal Receives idle position state (ON/OFF) Accelerator pedal position signal Receives accelerator pedal position (angle) Engine speed signal Receives engine speed TCM CAN communication Current gear position signal Receives a current gear position Shift position signal Receives a selector lever position Output shaft revolution signal Receives the number of revolutions of output shaft Input shaft revolution signal Receives the number of revolutions of input shaft ABS actuator and electric unit (control unit) CAN communication ABS malfunction signal Receives a malfunction state of ABS TCS malfunction signal Receives a malfunction state of TCS VDC malfunction signal Receives a malfunction state of VDC Nissan Murano Vehicle speed signal Receives the wheel speed of all four wheels Brake fluid pressure signal Receives brake fluid pressure Steering angle sensor CAN communication Steering angle sensor signal Receives the amount of rotation, rotational angle, and rotational direction of the steering wheel Combination meter CAN communication System selection signal Receives a selection state of each item in "Emergency Brake" selection with the combination meter Sonar control unit CAN communication Sonar sensor signal Receives obstacle information (existence & distance) BCM CAN communication Stop lamp switch signal Receives an operational state of the brake pedal Output Signal Item Reception unit Signal name Description ECM CAN communication Torque down request signal Transmits a signal to control the electric throttle control actuator...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Power Steering Fluid (PSF)
- Tire rotation
- All-Wheel Drive (AWD) (if so equipped)
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
