Nissan Murano: Srs Air Bag Control System :: Dtc/circuit Diagnosis / B0099 Satellite Sensor
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen items (Trouble diagnosis content) | DTC detecting condition | |
|---|---|---|---|
| B0099-93 |
SATELLITE SENSOR [RESET] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B0099-88 |
SATELLITE SENSOR [OPEN] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B0099-86 |
SATELLITE SENSOR [UNMATCH] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B0099-81 |
SATELLITE SENSOR [COMM ERR] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B0099-28 |
SATELLITE SENSOR [OFFSET ERR] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B0099-25 |
SATELLITE SENSOR [SELF-DIAG ERR] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B0099-24 |
SATELLITE SENSOR [UPPER LIMIT ERR] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B0099-23 |
SATELLITE SENSOR [LOWER LIMIT ERR] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B0099-12 |
SATELLITE SENSOR [VB-SHORT] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
| B0099-11 |
SATELLITE SENSOR [GND-SHORT] [Roll Over Sensor (Subfault)] |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | Satellite sensor | ||
| Threshold | — | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
[RESET], [COMM ERR]
-
Connection malfunction of harness or connector
-
Internal malfunction of other satellite sensor
-
Internal malfunction of air bag diagnosis sensor unit
[OPEN]
-
Connection malfunction or open circuit of harness or connector
-
Internal malfunction of other satellite sensor
-
Internal malfunction of air bag diagnosis sensor unit
[UNMATCH]
-
Air bag diagnosis sensor unit and other satellite sensor is different from the part specified
[OFFSET ERR], [SELF-DIAG ERR], [LOWER LIMIT ERR], [UPPER LIMIT ERR]
-
Internal malfunction of other satellite sensor
-
Internal malfunction of air bag diagnosis sensor unit
[VB-SHORT]
-
Connection malfunction or short circuit to power supply of harness and connector
-
Internal malfunction of other satellite sensor
-
Internal malfunction of air bag diagnosis sensor unit
[GND-SHORT]
-
Connection malfunction or short circuit to ground of harness and connector
-
Internal malfunction of other satellite sensor
-
Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
CHECK SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch ON.
-
Select "Self Diagnostic Result" mode of "AIR BAG".
-
Check for DTC.
Is the DTC detected?
YES>>(Current DTC) Refer to DTC Diagnosis Procedure.
YES>>(Past DTC) GO TO 2.
NO>>Inspection End.
ERASE SELF DIAGNOSTIC RESULT
CONSULT
Erase the DTC.
Can the DTC be erased?
YES>>Inspection End.
NO>>Refer to DTC Diagnosis Procedure.
DTC CONFIRMATION PROCEDURE
CHECK SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch ON.
-
Check the air bag warning lamp status. Refer to SRS Operation Check.
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO>>Inspection End.
WARNING:
-
Before servicing, ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)
-
Never use unspecified tester or other measuring device.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0099–86] >>GO TO 4.
Other than the above >>GO TO 2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Replace harness connector.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Replace wiring harness.
REPLACE SATELLITE SENSOR
-
Replace satellite sensor. Refer to Removal and Installation.
-
Perform DTC confirmation procedure. Refer to DTC Description.
Is DTC detected?
YES>>GO TO 5.
NO>>Inspection End.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
-
Replace air bag diagnosis sensor unit. Refer to Removal and Installation.
-
Perform DTC confirmation procedure. Refer to DTC Description.
Is DTC detected?
YES>>GO TO 1.
NO>>Inspection End.
B0091 Front Side Air Bag Satellite Sensor Lh
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen items
(Trouble diagnosis content) DTC detecting condition
B0091-93
B-PILLAR SAT SEN LH
[RESET]
Diagnosis condition
When ignition switch is ON...
B00a0 Occupant Classification System Control Unit
DTC Description
DESCRIPTIONDTC B00A0 OCCUPANT CLASSIFICATION SYSTEM (OCS)The OCS control unit is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor the OCS for failures and interruptions in communication between the OCS control unit and the air bag diagnosis sensor unit...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Transfer Case
Exploded View Oil seal Transfer cover Filler plug Gasket Drain plug Oil seal O-ring Ring gear bearing adjusting shim (transfer cover side) Ring gear bearing (transfer cover side) Drive shaft oil seal Ring gear shaft Ring gear bearing (transfer case side) Ring gear bearing adjusting shim (transfer case side) Ring gear Baffle plate Transfer case Plug O-ring Oil seal Dowel pin Drive pinion Drive pinion adjusting shim O-ring Pinion bearing assembly Oil seal Dust cover Companion flange Pinion lock nut Oil seal lip Comply with the assembly procedure when tightening...
Nissan Murano (Z52) 2015-2024 Service Manual: Hazard Switch Circuit
Component Function Check CHECK HAZARD SWITCH SIGNAL CONSULT Ignition switch ON. Select “HAZARD SW” in “Data Monitor” mode of “BCM(FLASHER)”. While operating the hazard switch, check the monitor status. Monitor item Condition Monitor status HAZARD SW Hazard switch ON On OFF Off Is the inspection result normal? YES>> Hazard switch circuit is normal...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- GAS STATION INFORMATION
- Warning lights
- High Beam Assist (if so equipped)
- New on site
- Most important about car
Autolight system
The autolight system allows the headlights to turn on and off automatically. The autolight system can:
Turn on the headlights, front parking, tail, license plate and instrument panel lights automatically when it is dark. Turn off all the lights (except daylight running lights) when it is light. Keep all the lights on for a period of time after you place the ignition switch in the OFF position and all doors are closed.