Nissan Murano: Mirrors / Automatic anti-glare rearview mirror (if so equipped)
The inside mirror is designed so that it automatically dims during night time conditions and according to the intensity of the headlights of the vehicle following you. The automatic anti-glare feature is activated when the ignition switch is in the ON position.
NOTE:
Do not hang any objects over the sensors
or apply glass cleaner to the
sensors.
Doing so will reduce the sensitivity
of the sensors, resulting in improper operation.
The indicator light 
will
illuminate when
the automatic anti-glare feature is operating.
To turn off the anti-glare feature, press the O button. The indicator light will turn off.
To turn on the anti-glare feature, press the | button. The indicator light will turn on.
For information on HomeLink® Universal Transceiver operation, refer to the “HomeLink® Universal Transceiver” in the “Instruments and controls” section of this manual.
Manual anti-glare rearview mirror (if so equipped)
Use the night position to reduce
glare
from the headlights of vehicles behind you
at night.
Use the day position when
driving in
daylight hours...
Outside mirrors
WARNING
Do not adjust the mirrors while driving.
You could lose control of your vehicle
and cause an accident.
Objects viewed in the outside mirror
on the passenger side are closer than
they appear...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: B2604 Pnp/clutch Sw
DTC Description DTC DETECTION LOGICNOTE: If DTC B2604 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to DTC Description. If DTC B2604 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010...
Nissan Murano (Z52) 2015-2024 Service Manual: B2724 Sonar Control Unit
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2724–23 SONAR CONTROL UNIT (Sonar control unit) — Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (under voltage) Diagnosis delay time — B2724–24 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (over voltage) Diagnosis delay time — B2724–44 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (RAM failure) Diagnosis delay time — B2724–45 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (ROM failure) Diagnosis delay time — B2724–46 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (EEPROM failure) Diagnosis delay time — B2724–48 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (internal software execution failure) Diagnosis delay time — B2724–49 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (basic chip set failure) Diagnosis delay time — B2724–55 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (not configured) Diagnosis delay time — B2724–86 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (SPI comm failure) Diagnosis delay time — B2724–87 Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Sonar ECU internal failure (high side switch failure) Diagnosis delay time — POSSIBLE CAUSE Charging system malfunction Sonar control unit power supply or ground circuit Sonar control unit configuration Sonar control unit FAIL-SAFE Off indicator blinks periodically (500ms ON, 500ms OFF)...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Shift lock release
- GAS STATION INFORMATION
- Checking engine oil level
- New on site
- Most important about car
Autolight system
The autolight system allows the headlights to turn on and off automatically. The autolight system can:
Turn on the headlights, front parking, tail, license plate and instrument panel lights automatically when it is dark. Turn off all the lights (except daylight running lights) when it is light. Keep all the lights on for a period of time after you place the ignition switch in the OFF position and all doors are closed.