Nissan Murano: Wiper & Washer :: Symptom Diagnosis / Wiper and Washer System Symptoms
CAUTION:
Perform the “Self Diagnostic Result” with Consult before performing the diagnosis by symptom. Perform the diagnosis by DTC if DTC is detected.
| Symptom | Probable malfunction location | Inspection item | |
|---|---|---|---|
| Front wiper does not operate in . . . | HI only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
Front wiper motor (HI) circuit Refer to Component Function Check. |
||
|
Front wiper request signal
|
BCM(WIPER) “Data Monitor” “FR WIPER HI” Refer to Diagnosis Description. |
||
| LO only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
|
Front wiper motor (LO) circuit Refer to Component Function Check. |
||
|
Front wiper request signal
|
BCM(WIPER) “Data Monitor” “FR WIPER LOW” Refer to Diagnosis Description. |
||
| INT only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
| HI, LO and INT |
SYMPTOM DIAGNOSIS “FRONT WIPER DOES NOT OPERATE” Refer to Diagnosis Procedure. |
||
| Front wiper does not stop in . . . | HI only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
Front wiper request signal
|
BCM(WIPER) “Data Monitor” “FR WIPER HI” Refer to Diagnosis Description. |
||
| IPDM E/R | — | ||
| LO only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
|
Front wiper request signal
|
BCM(WIPER) “Data Monitor” “FR WIPER LOW” Refer to Diagnosis Description. |
||
| IPDM E/R | — | ||
| INT only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
| Front wiper does not operate normally in. . . | Sensitivity adjustment cannot be performed. |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
| BCM | — | ||
| Wiper is not linked to the washer operation. |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
| BCM | — | ||
| Does not return to stop position. [Repeatedly operates for 10 seconds and then stops for 20 seconds. (Fail-safe)] |
|
Front wiper stop position signal circuit Refer to Component Function Check. |
|
| Rear wiper does not operate in. . . | ON only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
| INT only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
| ON and INT |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
|
Rear wiper motor circuit Refer to Component Function Check. |
||
| Rear wiper does not stop in. . . | ON only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
| INT only |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
| Rear wiper does not operate normally in. . . | Wiper is not linked to the washer operation. |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
| BCM | — | ||
| Rear wiper does not return to the stop position. [Stops after a five-second operation. (Fail-safe)] |
|
Rear wiper stop position signal circuit Refer to Component Function Check. |
|
| Front and rear washer motor does not operate. | Front and rear washer motor does not operate when washing the windshield. |
|
Combination switch (wiper and washer switch) Refer to Symptom Table. |
|
Front and rear washer motor circuit Refer to Diagnosis Procedure. |
||
Normal Operating Condition
Description
FRONT WIPER MOTOR PROTECTION FUNCTION
IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance) such as a large amount of snow is detected during the front wiper operation...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: P2135 Tp Sensor
DTC Description DTC DETECTION LOGICRationally incorrect voltage is sent to ECM compared with the signals from TP sensor 1 and TP sensor 2. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2135 TP SENSOR-B1 (Throttle/Pedal position sensor/switch “A” / “B” voltage correlation) Diagnosis condition Start engine and let it idle Signal (terminal) TP sensor 1 signal and TP sensor 2 signal Threshold Rationally incorrect voltage is sent to ECM compared with the signals from TP sensor 1 and TP sensor 2 Diagnosis delay time — POSSIBLE CAUSE Harness or connector (TP sensor 1 or 2 circuit is open or shorted...
Nissan Murano (Z52) 2015-2024 Service Manual: Combination Switch
Exploded View 1. Combination switch 2. Combination switch harness connector Removal and Installation REMOVALDisconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to Exploded View. Remove the steering column covers...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- GAS STATION INFORMATION
- Indicator lights
- Vehicle Dynamic Control (VDC) OFF switch
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
