Nissan Murano: Heater & Air Conditioning Control System :: Dtc/circuit Diagnosis / U1010 Control Unit(can)

Nissan Murano (Z52) 2015-2024 Service Manual / Ventilation, Heater & Air Conditioner / Heater & Air Conditioning Control System :: Dtc/circuit Diagnosis / U1010 Control Unit(can)

DTC Description

Initial diagnosis of A/C auto amp.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U1010

CONTROL UNIT(CAN)

[Control unit (CAN)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold -
Diagnosis delay time -

POSSIBLE CAUSE

A/C auto amp.

FAIL-SAFE

DTC Confirmation Procedure

PERFORM SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

Inspection End.

DTC Diagnosis Procedure

REPLACE A/C AUTO AMP.

Replace A/C auto amp. Refer to Removal and Installation.

>>

Inspection End.

    U1000 Can Comm Circuit

    DTC Description CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Murano vehicle multiplex communication system with high data communication speed and excellent error detection ability...

    B2578 in-Vehicle Sensor

    DTC Description DTC DETECTION LOGICNOTE: If DTC is displayed along with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to DTC Description...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: P1078 Evt Control Position Sensor


    DTC Description DTC DETECTION LOGICAn excessively high or low voltage from the sensor is sent to ECM. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1078 EXH TIM SEN/CIRC-B1 [Exhaust valve timing (EVT) control position sensor (bank 1) circuit] Diagnosis condition Start engine and let it idle Signal (terminal) Voltage signal transmitted from EVT control position sensor to ECM Threshold An excessively high or low voltage from the sensor is sent to ECM Diagnosis delay time — P1084 EXH TIM SEN/CIRC-B2 [Exhaust valve timing (EVT) control position sensor (bank 2) circuit] Diagnosis condition Start engine and let it idle Signal (terminal) Voltage signal transmitted from EVT control position sensor to ECM Threshold An excessively high or low voltage from the sensor is sent to ECM Diagnosis delay time — POSSIBLE CAUSEDTC P1078 Harness or connectors [EVT control position sensor (bank 1) circuit is open or shorted...

    Nissan Murano (Z52) 2015-2024 Service Manual: Service Data and Specifications (sds). Service Data and Specifications (sds)


    General Specifications Applied model Axle AWD Engine VQ35DE Transaxle CVT Propeller shaft model C-CVJ-C Number of joints 3 Joint type 1st joint Universal (Shell type) 2nd joint CVJ type 3rd joint Universal (Shell type) Coupling method Transfer side Flange type Rear final drive side Flange type Shaft length 1st (Spider to CVJ joint center) 1265 mm (49...

    Categories

    Unfastening the seat belts. Checking seat belt operation

    Unfastening the seat belts

    Nissan Murano. Unfastening the seat belts. Checking seat belt operation

    To unfasten the seat belt, press the button on the buckle Nissan Murano. Unfastening the seat belts. Checking seat belt operation. The seat belt automatically retracts.

    read more

     
    Copyright © 2026 www.nimurano.com