Nissan Murano: Automatic Drive Positioner :: Dtc/circuit Diagnosis / Sliding Switch
DATA MONITOR
CONSULT
-
Select “SLIDE SW-FR”, “SLIDE SW-RR” in “Data Monitor” mode of “AUTO DRIVE POS.”.
-
Check that the function operates normally according to the following conditions:
| Monitor item | Condition | Status | |
|---|---|---|---|
| SLIDE SW-FR | Sliding switch (forward) | Operate | ON |
| Release | OFF | ||
| SLIDE SW-RR | Sliding switch (backward) | Operate | ON |
| Release | OFF | ||
Is the inspection result normal?
YES>>Inspection End.
NO>>Perform diagnosis procedure. Refer to Diagnosis Procedure.
CHECK SLIDING SWITCH SIGNAL
-
Ignition switch OFF.
-
Check voltage between driver seat control unit harness connector and ground.
| (+) | (–) | Condition |
Voltage (Approx.) | ||
|---|---|---|---|---|---|
| Driver seat control unit | |||||
| Connector | Terminals | ||||
| B209 | 9 | Ground | Sliding switch | Operate (backward) | 0V |
| Release | Battery voltage | ||||
| 25 | Operate (forward) | 0V | |||
| Release | Battery voltage | ||||
Is the inspection result normal?
YES>>GO TO 5.
NO>>GO TO 2.
CHECK SLIDING SWITCH CIRCUIT
-
Ignition switch OFF.
-
Disconnect driver seat control unit and power seat switch LH.
-
Check continuity between driver seat control unit harness connector and power seat switch LH harness connector.
Driver seat control unit Power seat switch LH Continuity Connector Terminal Connector Terminal B209 25 B208 7 Yes 9 8 -
Check continuity between driver seat control unit harness connector and ground.
Driver seat control unit Ground Continuity Connector Terminal B209 25 No 9
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK DRIVER SEAT CONTROL UNIT OUTPUT
-
Connect the driver seat control unit.
-
Ignition switch ON.
-
Check voltage between driver seat control unit harness connector and ground.
| (+) | (–) |
Voltage (Approx.) | |
|---|---|---|---|
| Driver seat control unit | |||
| Connector | Terminal | ||
| B209 | 25 | Ground | Battery voltage |
| 9 | |||
Is the inspection result normal?
YES>>GO TO 4.
NO>>Replace driver seat control unit. Refer to Removal and Installation.
CHECK SLIDING SWITCH
Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Replace power seat switch LH. Refer to Removal and Installation.
CHECK INTERMITTENT INCIDENT
Refer to Intermittent Incident.
Is the inspection result normal?
YES>>Replace driver seat control unit. Refer to Removal and Installation.
NO>>Repair or replace malfunctioning part.
CHECK SLIDING SWITCH
-
Ignition switch OFF.
-
Disconnect power seat switch LH.
-
Check continuity between power seat switch LH terminals.
Power seat switch LH Condition Continuity Terminal 3 8 Sliding switch (backward) Operate Yes Release No 7 Sliding switch (forward) Operate Yes Release No
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace power seat switch LH. Refer to Removal and Installation.
Power Supply and Ground Circuit. Driver Seat Control Unit
Diagnosis Procedure
NOTE:
Do not disconnect the battery negative terminal and the driver seat control unit connector until DTC is confirmed with CONSULT...
Tilt Switch
Component Function Check
DATA MONITOR
CONSULT
Select “TILT SW-UP”, “TILT SW-DOWN” in “Data Monitor” mode of “AUTO DRIVE POS.”.
Check that the function operates normally according to the following conditions:
Monitor item Condition Status
TILT SW-UP
Tilt switch (up)
Operate
ON
Release
OFF
TILT SW-DOWN
Tilt switch (down)
Operate
ON
Release
OFF
Is the inspection result normal?
YES>>
Inspection End...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Seat Back Blower
Component Function Check CHECK SEAT BACK BLOWER FUNCTION When turning the climate controlled seat switch to the COOL mode position, check that the seat back blower is operated in each specific mode. Is the inspection result normal? YES>> Inspection End...
Nissan Murano (Z52) 2015-2024 Service Manual: P0197 Eot Sensor
DTC Description DTC DETECTION LOGIC An excessively low voltage from the sensor is sent to ECM. An excessively high voltage from the sensor is sent to ECM. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0197 EOT SEN/CIRC (Engine oil temperature sensor circuit low) Diagnosis condition Start engine and let it idle Signal (terminal) Voltage signal transmitted from engine oil temperature sensor to ECM Threshold An excessively low voltage from the sensor is sent to ECM Diagnosis delay time — P0198 EOT SEN/CIRC (Engine oil temperature sensor circuit high) Diagnosis condition Start engine and let it idle Signal (terminal) Voltage signal transmitted from engine oil temperature sensor to ECM Threshold An excessively high voltage from the sensor is sent to ECM Diagnosis delay time — POSSIBLE CAUSEP0197 Harness or connectors (The sensor circuit is open or shorted...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Checking engine oil level
- Fuel recommendation
- Jacking up vehicle and removing the damaged tire
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
