Nissan Murano: Automatic Drive Positioner :: Dtc/circuit Diagnosis / Power Supply and Ground Circuit. Driver Seat Control Unit
NOTE:
Do not disconnect the battery negative terminal and the driver seat control unit connector until DTC is confirmed with CONSULT.
CHECK FUSE
Check that the following fusible link is not blown:
| Signal name | Fusible link No. | Capacity |
|---|---|---|
| Battery power supply | L | 40 A |
Is the inspection result normal?
YES>>GO TO 2.
NO>>Replace the blown fusible link after repairing the affected circuit if a fuse is blown.
CHECK POWER SUPPLY CIRCUIT
-
Ignition switch OFF.
-
Disconnect driver seat control unit.
-
Check voltage between driver seat control unit harness connector and ground.
| (+) | (–) | Condition |
Voltage (Approx.) | |
|---|---|---|---|---|
| Driver seat control unit | ||||
| Connector | Terminal | |||
| B210 | 37 | Ground | Ignition switch OFF | Battery voltage |
Is the inspection result normal?
YES>>GO TO 2.
NO>>Check the following:
-
Repair or replace harness.
-
Circuit breaker-2.
CHECK GROUND CIRCUIT
Check continuity between the driver seat control unit harness connector and ground.
| Driver seat control unit | Ground | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B210 | 39 | Yes | |
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
PERFORM ADDITIONAL SERVICE
Perform additional service when removing battery negative terminal.
>>
Refer to Work Procedure’.
B2130 Eeprom
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition
B2130
EEPROM
(EEPROM malfunction)
Diagnosis condition
—
Signal (terminal)
—
Threshold
Driver seat control unit detected a CPU malfunction...
Sliding Switch
Component Function Check
DATA MONITOR
CONSULT
Select “SLIDE SW-FR”, “SLIDE SW-RR” in “Data Monitor” mode of “AUTO DRIVE POS.”.
Check that the function operates normally according to the following conditions:
Monitor item Condition Status
SLIDE SW-FR
Sliding switch (forward)
Operate
ON
Release
OFF
SLIDE SW-RR
Sliding switch (backward)
Operate
ON
Release
OFF
Is the inspection result normal?
YES>>
Inspection End...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: U1300 Av Comm Circuit
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1300–01 AV communication circuit (AV communication circuit) Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold — Diagnosis delay time — POSSIBLE CAUSE AV communication circuit AV control unit Combination meter FAIL-SAFEAV communication is inoperative DTC Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Ignition switch ON...
Nissan Murano (Z52) 2015-2024 Owners Manual: Precautions on child restraints
WARNING Failure to follow the warnings and instructions for proper use and installation of child restraints could result in serious injury or death of a child or other passengers in a sudden stop or collision: The child restraint must be used and installed properly...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Turning the AEB system on/off
- High Beam Assist (if so equipped)
- Checking engine oil level
- New on site
- Most important about car
Driver and passenger supplemental knee air bag
Driver’s side
The knee air bag is located in the knee bolster, on the driver’s and passenger’s side. All of the information, cautions and warnings in this manual apply and must be followed. The knee air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain collisions.
Passenger’s side
