Nissan Murano: Push-button ignition switch / NISSAN Vehicle Immobilizer System
The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered key.
If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following procedure:
- Leave the ignition switch in the ON position for approximately 5 seconds.
- Place the ignition switch in the OFF or LOCK position, and wait approximately 10 seconds.
- Repeat steps 1 and 2.
- Restart the engine while holding the device (which may have caused the interference) separate from the registered key.
If the no start condition re-occurs, NISSAN recommendsplacing the registered key on a separate key ring to avoid interference from other devices.
NISSAN Intelligent Key® battery discharge
If the battery of the NISSAN Intelligent Key®
is discharged, or environmental conditions
interfere with the Intelligent Key operation,
start the engine according to the following
procedure:
Place the shift lever in the P (Park) position...
Before starting the engine
Make sure the area around the vehicle is
clear.
Check fluid levels such as engine oil,
coolant, brake fluid, and windshieldwasher
fluid as frequently as possible,
or at least whenever you refuel...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Rear Axle :: Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
NVH Troubleshooting Chart Use chart below to find the cause of the symptom. If necessary, repair or replace these parts. Reference — Disassembly and Assembly — Exploded View — NVH Troubleshooting Chart NVH Troubleshooting Chart NVH Troubleshooting Chart Inspection NVH Troubleshooting Chart NVH Troubleshooting Chart Inspection NVH Troubleshooting Chart Possible cause and SUSPECTED PARTS Excessive joint angle Joint sliding resistance Imbalance Improper installation, looseness Parts interference PROPELLER SHAFT (AWD) DIFFERENTIAL (AWD) REAR SUSPENSION REAR AXLE TIRE WHEEL DRIVE SHAFT (AWD) BRAKE Symptom DRIVE SHAFT Noise × × × × × × × × × Shake × × × × × × × × REAR AXLE Noise × × × × × × × × × Shake × × × × × × × × Vibration × × × × × × Shimmy × × × × × × Shudder × × × × × Poor quality ride or handling × × × × × Inspect Rear Axle for cracks or damage...
Nissan Murano (Z52) 2015-2024 Service Manual: Service Data and Specifications (sds). Service Data and Specifications (sds)
Capacity (US qt, Imp qt) Engine coolant capacity* 8.7 (9-1/4, 7-5/8) *: Includes 0.8L with coolant reservoir tank at MAX level. Thermostat Valve opening temperature 82°C (180°F) Full-open lift amount 8.6 mm / 95°C (0.339 in / 203°F) Valve closing temperature 77°C (171°F) Radiator Unit: kPa (kg/cm2, psi) Cap relief pressure Standard 118 ± 9...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Indicator lights
- How to enable/disable the LDW system
- GAS STATION INFORMATION
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
