Nissan Murano: Road Wheels & Tires :: Symptom Diagnosis / Low Tire Pressure Warning Lamp Does Not Turn on
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.
-
Activate and display TPMS sensor IDs
-
Display tire pressure reported by the TPMS sensor
-
Read TPMS DTCs
-
Register TPMS sensor IDs
PERFORM SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of "BCM(AIR PRESSURE MONITOR)".
-
Check DTC.
Is DTC U1000 detected?
YES>>Refer to Trouble Diagnosis Flow Chart.
NO>>GO TO 2.
CHECK COMBINATION METER
Check combination meter operation. Refer to Diagnosis Description.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Replace combination meter. Refer to Removal and Installation.
CHECK LOW TIRE PRESSURE WARNING LAMP
Disconnect BCM harness connector.
Does the low tire pressure warning lamp activate?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Check combination meter operation.
Tpms
Symptom Table
LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART Diagnosis items
Symptom
(Ignition switch ON) Low tire pressure warning lamp Cause Action
Low tire pressure warning lamp
The low tire pressure warning lamp illuminates for 1 second, then turns OFF...
Low Tire Pressure Warning Lamp Stays on
Diagnosis Procedure
CHECK BCM CONNECTORS
Ignition switch OFF.
Disconnect BCM connectors.
Check terminals for damage or loose connections.
Is the inspection result normal?
YES>>
GO TO 2...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Front Suspension :: Unit Removal and Installation. Front Suspension Member
Exploded View 1. Front suspension member 2. Rebound stopper 3. Front suspension member stay Front Removal and Installation REMOVALRemove engine and transmission with front suspension member. Lift engine and transmission off suspension member...
Nissan Murano (Z52) 2015-2024 Service Manual: P0182 Ftt Sensor
DTC Description DTC DETECTION LOGIC An excessively low voltage from the sensor is sent to ECM. An excessively high voltage from the sensor is sent to ECM. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0182 FTT_SEN/CIRCUIT (Fuel temperature sensor “A” circuit low) Diagnosis condition Ignition switch ON Signal (terminal) Voltage signal transmitted from fuel tank temperature sensor to ECM Threshold An excessively low voltage from the sensor is sent to ECM Diagnosis delay time — P0183 FTT_SEN/CIRCUIT (Fuel temperature sensor “A” circuit high) Diagnosis condition Ignition switch ON Signal (terminal) Voltage signal transmitted from fuel tank temperature sensor to ECM Threshold An excessively high voltage from the sensor is sent to ECM Diagnosis delay time — POSSIBLE CAUSEP0182 Harness or connectors (The sensor circuit is open or shorted...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- High Beam Assist (if so equipped)
- Vehicle Dynamic Control (VDC) OFF switch
- Passenger compartment
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
