Nissan Murano: Door & Lock :: Dtc/circuit Diagnosis / Integrated Homelink Transceiver
CHECK FUNCTION
Check that system receiver (garage door opener, etc.) operates with original hand-held transmitter.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Receiver or hand-held transmitter is malfunctioning.
CHECK ILLUMINATION
-
Ignition switch OFF.
-
Does red light of transceiver illuminate when any transceiver button is pressed?
Is the inspection result normal?
YES>>GO TO 3.
NO>>Refer to Diagnosis Procedure.
CHECK TRANSMITTER
Check transceiver with Tool*.
*:For details, refer to Technical Service Bulletin.
Is the inspection result normal?
YES>>Receiver or hand-held transmitter malfunction, not Nissan Murano vehicle related.
NO>>Replace auto anti-dazzling inside mirror (HomeLink® universal transceiver). Refer to Removal and Installation.
CHECK POWER SUPPLY
-
Ignition switch OFF.
-
Disconnect auto anti-dazzling inside mirror (HomeLink® universal transceiver) connector.
-
Check voltage between auto anti-dazzling inside mirror (HomeLink® universal transceiver) harness connector and ground.
|
Auto anti-dazzling inside mirror (HomeLink® universal transceiver) | – | Condition |
Voltage (Approx.) | |
|---|---|---|---|---|
| Connector | Terminal | |||
| R7 | 10 | Ground | Ignition switch position: OFF | Battery voltage |
| Ignition switch position: ON | ||||
| 6 | Ignition switch position: OFF | 0 | ||
| Ignition switch position: ON | Battery voltage | |||
Is the inspection result normal?
YES>>GO TO 2.
NO>>Check the following items:
-
10A fuse No. 29 located in the fuse block (J/B).
-
10A fuse No. 9 located in the fuse block (J/B).
-
Harness for open or short between fuse and auto anti-dazzling inside mirror (HomeLink® universal transceiver).
CHECK GROUND CIRCUIT
Check continuity between auto anti-dazzling inside mirror (HomeLink® universal transceiver) harness connector and ground.
|
Auto anti-dazzling inside mirror (HomeLink® universal transceiver) |
Ground | Continuity | |
| Connector | Terminal | ||
| R7 | 8 | Yes | |
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair harness.
CHECK INTERMITTENT INCIDENT
Refer to Intermittent Incident.
>>
Inspection End.
Hood Switch
Component Function Check
CHECK FUNCTION
CONSULT
Select “HOOD SW” and "HOOD SW 2" in “Data Monitor” mode of “IPDM E/R”.
Check “HOOD SW” and "HOOD SW 2" indication under the following conditions:
Monitor item Condition Indication
HOOD SW
Hood
Open
OFF
Close
ON
HOOD SW 2
Open
ON
Close
OFF
Is the indication normal?
YES>>
Hood switch is OK...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: B2e33 Ecall Button
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2E33 ECALL BUTTON (Ecall button) Diagnosis condition When ignition switch is ON. Signal (terminal) SOS switch LED signal (terminal 5) Threshold — Diagnosis delay time 1 second or more POSSIBLE CAUSE SOS switch LED signal circuit SOS switch TCU FAIL-SAFE Telematics system does not function (Only SOS call does not operate) SOS switch LED indicator is turned OFF DTC Confirmation Procedure PERFORM DTC CONFIRMATION PROCEDURE CONSULT Ignition switch ON...
Nissan Murano (Z52) 2015-2024 Service Manual: Engine Mechanical :: Unit Disassembly and Assembly. Cylinder Block
Exploded View 1. Reinforcement plate 2. Drive plate 3. Rear oil seal retainer 4. Rear oil seal 5. Sub harness 6. Knock sensor 7. Cylinder block 8. Thrust bearing (upper) 9. Main bearing (upper) 10. Crankshaft 11...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Memory storage function (key-link)
- Rear bench seat adjustment
- High Beam Assist (if so equipped)
- New on site
- Most important about car
Fuel gauge
The gauge indicates the approximate fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the ignition switch is placed in the OFF position.
