Nissan Murano: Door & Lock :: Dtc/circuit Diagnosis / Hood Switch
CHECK FUNCTION
CONSULT
-
Select “HOOD SW” and "HOOD SW 2" in “Data Monitor” mode of “IPDM E/R”.
-
Check “HOOD SW” and "HOOD SW 2" indication under the following conditions:
| Monitor item | Condition | Indication | |
|---|---|---|---|
| HOOD SW | Hood | Open | OFF |
| Close | ON | ||
| HOOD SW 2 | Open | ON | |
| Close | OFF | ||
Is the indication normal?
YES>>Hood switch is OK.
NO>>Go to Diagnosis Procedure.
CHECK HOOD SWITCH SIGNAL CIRCUITS
-
Ignition switch OFF.
-
Disconnect hood switch connector.
-
Check voltage between hood switch harness connector and ground.
| (+) | (–) |
Voltage (V) (Approx.) | |
|---|---|---|---|
| Hood switch | |||
| Connector | Terminal | ||
| E205 | 1 | Ground | Battery voltage |
| 2 | |||
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
CHECK HOOD SWITCH SIGNAL CIRCUITS
-
Disconnect IPDM E/R connector.
-
Check continuity between IPDM E/R harness connector and hood switch harness connector.
IPDM E/R Hood switch Continuity Connector Terminal Connector Terminal E218 94 E205 1 Yes 96 2 -
Check continuity between IPDM E/R harness connector and ground.
IPDM E/R Ground Continuity Connector Terminal E218 94 No 96
Is the inspection result normal?
YES>>Replace IPDM E/R. Refer to Removal and Installation.
NO>>Repair or replace harness.
CHECK HOOD SWITCH GROUND CIRCUIT
Check continuity between hood switch harness connector and ground.
| Hood switch | Ground | Continuity | |
| Connector | Terminal | ||
| E205 | 3 | Yes | |
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace harness.
CHECK HOOD SWITCH
Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Replace hood switch. Refer to Removal and Installation.
CHECK INTERMITTENT INCIDENT
Refer to Intermittent Incident.
>>
Inspection End.
CHECK HOOD SWITCH
-
Ignition switch OFF.
-
Disconnect hood switch connector.
-
Check continuity between hood switch terminals.
Hood switch Condition Continuity Terminal 1 3 Hood switch Press Yes Release No 2 Press No Release Yes
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace hood switch. Refer to Removal and Installation.
Automatic Back Door Warning Buzzer
Diagnosis Procedure
CHECK AUTOMATIC BACK DOOR WARNING BUZZER GROUND CIRCUIT
Ignition switch OFF.
Disconnect automatic back door warning buzzer connector...
Integrated Homelink Transceiver
Component Function Check
CHECK FUNCTION
Check that system receiver (garage door opener, etc.) operates with original hand-held transmitter.
Is the inspection result normal?
YES>>
GO TO 2...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Turn Signal Lamp Circuit
Component Function Check CHECK TURN SIGNAL LAMP CONSULT Select "FLASHER" in “Active Test” mode of “BCM(FLASHER)”. While operating the test items, check that the turn signal lamp blinks. LH : Turn signal lamp LH blinking RH : Turn signal lamp RH blinking OFF : The turn signal lamp OFF Is the inspection result normal? YES>> Turn signal lamp circuit is normal...
Nissan Murano (Z52) 2015-2024 Owners Manual: USB/iPod® charging port
2nd row There are USB/iPod® charging ports located in the 2nd row on the back of the center console. These ports will charge compatible devices. NOTE: Only the USB connection port(s) located below the instrument panel will allow operation of USB/iPod® devices through the audio system...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Tire rotation
- Shift lock release
- Power Steering Fluid (PSF)
- New on site
- Most important about car
Luggage hooks
When securing items using luggage hooks located on the back of the seat or side finisher do not apply a load over more than 6.5 lbs. (29 N) to a single hook.
The luggage hooks that are located on the floor should have loads less than 110 lbs. (490 N) to a single hook.
