Nissan Murano: Dtc/circuit Diagnosis / Headlamp (hi) Circuit

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Controls / Exterior Lighting System :: Led Headlamp / Dtc/circuit Diagnosis / Headlamp (hi) Circuit

Component Function Check

CHECK HEADLAMP (HI) OPERATION

CONSULT

  1. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R”.

  2. While operating the test items, check that the headlamp (HI) blinks.

    Hi : Headlamp (HI) blinks (ON/OFF is repeated 1 second each).
    Off : Headlamp (HI) OFF

Is the inspection result normal?

YES>>

Headlamp (HI) circuit is normal.

NO>>

Refer to Diagnosis Description.

Diagnosis Procedure

CHECK HEADLAMP (HI) FUSE

  1. Ignition switch OFF.

  2. Check that the following fuses are not blown:

    Component Location Fuse No. Capacity
    Headlamp HI (RH) IPDM E/R 34 10 A
    Headlamp HI (LH) 35

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace the blown fuse after repairing the affected circuit.

CHECK HEADLAMP (HI) OUTPUT VOLTAGE

CONSULT

  1. Disconnect applicable front combination lamp connector.

  2. Ignition switch ON.

  3. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R”.

  4. While operating the test items, check voltage between applicable front combination lamp harness connector and ground.

    + - Test item

    Voltage

    (Approx.)
    Front combination lamp
    Connector Terminal
    RH E243 2 Ground EXTERNAL LAMPS Hi Battery voltage
    Off 0 V
    LH E247 Hi Battery voltage
    Off 0 V

Is the inspection result normal?

YES>>

Perform the LED headlamp diagnosis. Refer to Diagnosis Procedure.

NO>>

GO TO 3.

CHECK HEADLAMP (HI) POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between IPDM E/R harness connector and front combination lamp harness connector.

    Front combination lamp IPDM E/R Continuity
    Connector Terminal Connector Terminal
    RH E243 2 E217 80 Yes
    LH E247 81

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis

    ..

    Daytime Running Light Relay Circuit

    Component Function Check CHECK DAYTIME RUNNING LIGHT OPERATION CONSULT Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R”. While operating the test items, check daytime running light operation...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: Radiator


    Exploded View 1. Clamp 2. Reservoir tank hose 3. Clamp 4. Clip 5. Clamp 6. Radiator cap 7. Clamp 8. CVT fluid cooler hose A 9. Radiator 10. O-ring 11. Radiator drain plug 12. CVT fluid cooler hose B 13...

    Nissan Murano (Z52) 2015-2024 Owners Manual: Front passenger’s power window switch, Rear power window switch


    Front passenger’s power window switch The passenger’s window switch operates only the corresponding passenger’s window. To open the window partially, push the switch down lightly until the desired window position is reached. To close the window partially, pull the switch up until the desired window position is reached...

    Categories

    LATCH (Lower Anchors and Tethers for CHildren) system

    Nissan Murano. LATCH (Lower Anchors and Tethers for CHildren) system

    LATCH system lower anchor locations - bench seat

    Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.

    read more

     
    Copyright © 2026 www.nimurano.com