Nissan Murano: Front Axle :: Removal and Installation / Front Drive Shaft Boot
Nissan Murano (Z52) 2015-2024 Service Manual / Transmission & Driveline / Front Axle :: Removal and Installation / Front Drive Shaft Boot
LH
| 1. | Shaft with damper | 2. | Circular clip | 3. | Dust shield |
| 4. | Housing | 5. | Snap ring | 6. | Spider assembly |
| 7. | Stopper ring | 8. | Boot | 9. | Boot band |
| 10. | Joint sub-assembly |  |
Wheel side |  |
Fill with Genuine NISSAN grease. |
RH
| 1. | Support bearing retainer | 2. | Housing | 3. | Boot |
| 4. | Shaft with damper | 5. | Joint sub-assembly | 6. | Circular clip |
| 7. | Boot band | 8. | Stopper ring | 9. | Spider assembly |
| 10. | Snap ring | 11. | Support bearing | 12. | Dust shield |
| 13. | Support bearing bracket | A. | Refer to Removal and Installation. | |
Wheel side |
|
Fill with Genuine NISSAN grease. |
Front Wheel Hub
Exploded View
1.
Cotter pin
2.
Nut retainer
3.
Disc brake rotor
4.
Wheel hub and bearing
5.
Wheel stud
6.
Splash guard
7.
Steering knuckle
Front
Removal and Installation
REMOVALRemove disc brake rotor...
Wheel Side
Removal and Installation
REMOVALRemove disc brake rotor. Refer to Removal and Installation.
Remove wheel sensor bolt (A) and position wheel sensor aside...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: P0452 Evap Control System Pressure Sensor
DTC Description DTC DETECTION LOGICAn excessively low voltage from the sensor is sent to ECM. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0452 EVAP SYS PRES SEN (Evaporative emission system pressure sensor/switch low) Diagnosis condition — Signal (terminal) Voltage signal transmitted from EVAP control system pressure sensor to ECM Threshold An excessively low voltage from the sensor is sent to ECM Diagnosis delay time — POSSIBLE CAUSE Harness or connectors (EVAP control system pressure sensor circuit is open or shorted...
Nissan Murano (Z52) 2015-2024 Service Manual: Glass & Window System :: Preparation. Preparation
Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-39570) Chassis Ear Locating the noise — (J-50397) NISSAN Squeak and Rattle Kit Repairing the cause of noise — (J-46534) Trim Tool Set Removing trim components Commercial Service Tool (TechMate No...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Tire rotation
- Jacking up vehicle and removing the damaged tire
- Memory storage function (key-link)
- New on site
- Most important about car
LATCH (Lower Anchors and Tethers for CHildren) system
LATCH system lower anchor locations - bench seat
Your vehicle is equipped with special anchor points that are used with LATCH system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint unless the combined weight of the child and child restraint exceeds 65 lbs. (29.5 kg). If the combined weight of the child and child restraint is greater than 65 lbs. (29.5 kg), use the vehicle’s seat belt (not the lower anchors) to install the child restraint. Be sure to follow the child restraint manufacturer’s instructions for installation.
Copyright © 2026 www.nimurano.com