Nissan Murano: Instruments and controls / Climate controlled seat switches (if so equipped)

The climate controlled seat warms up or
cools down the front seat by blowingwarm
or cool air from under the surface of the
seat. The climate control switch is located
on the center console.
The climate controlled seat can be operated
as follows:
- Place the ignition switch in the ON position.
- Turn the control knob
to
the heat
side
or the cool side
. The indicator
light
on the control knob will
illuminate.
- Adjust the desired amount of air using
the control knob. The climate controlled
seat blower remains on low
speed for approximately 60 seconds
after turning the switch on or selecting
the desired temperature.
- When the vehicle’s interior is warmed
or cooled, or before you leave the vehicle,
be sure to turn the control knob
to the off (center) position. The indicator
light
on the control knob goes
off
with the switch in the off (center) position.
To check the air filter for the climate controlled
seat, it is recommended that you
visit a NISSAN dealer.
WARNING
Do not use or allow occupants to use
the climate controlled seats if youor the
occupants cannot monitor seat temperatures
or have an inability to feel
pain in those body parts in contact with
the seat. Use of the climate controlled
seats by such people could result in serious
injury.
CAUTION
- The battery could run down if the climate
control seat is operated while
the engine is not running.
- Do not use the climate control seat for
extended periods or when no one is
using the seat.
- Do not put anything on the seat which
insulates heat, such as a blanket,
cushion, seat cover, etc. Otherwise,
the seat may become overheated.
- Do not place anything hard or heavy
on the seat or pierce it with a pin or
similar objects. This may result in
damage to the climate controlled
seat.
- Any liquid spilled on the seat should
be removed immediately with a dry
cloth.
- The climate controlled seat has an air
filter. Do not operate the climate controlled
seat without an air filter. This
may result in damage to the system.
- When cleaning the seat, never use
gasoline, benzine, thinner, or any
similar materials.
- If any malfunctions are found or the
climate controlled seat does not operate,
turn the switch off and have the
system checked. It is recommended
that you visit a NISSAN dealer for this
service.
To sound the horn, push near the horn icon
on the steering wheel.
WARNING
Do not disassemble the horn. Doing so
could affect proper operation of the
supplemental front air bag system...
WARNING
Do not use or allow occupants to use
the seat heater if you or the occupants
cannot monitor elevated seat temperatures
or have an inability to feel pain in
those body parts in contact with the
seat...
Other information:
System Description
SYSTEM DIAGRAMADAS CONTROL UNIT INPUT/OUTPUT SIGNAL ITEMInput Signal Item Transmit unit Signal name Description
ECM
CAN communication
Closed throttle position signal
Receives idle position state (ON/OFF)
Accelerator pedal position signal
Receives accelerator pedal position (angle)
Engine speed signal
Receives engine speed
TCM
CAN communication
Current gear position signal
Receives a current gear position
Shift position signal
Receives a selector lever position
Output shaft revolution signal
Receives the number of revolutions of output shaft
Input shaft revolution signal
Receives the number of revolutions of input shaft
ABS actuator and electric unit (control unit)
CAN communication
ABS malfunction signal
Receives a malfunction state of ABS
TCS malfunction signal
Receives a malfunction state of TCS
VDC malfunction signal
Receives a malfunction state of VDC
Nissan Murano Vehicle speed signal
Receives the wheel speed of all four wheels
Brake fluid pressure signal
Receives brake fluid pressure
Steering angle sensor
CAN communication
Steering angle sensor signal
Receives the amount of rotation, rotational angle, and rotational direction of the steering wheel
Combination meter
CAN communication
System selection signal
Receives a selection state of each item in "Emergency Brake" selection with the combination meter
Sonar control unit
CAN communication
Sonar sensor signal
Receives obstacle information (existence & distance)
BCM
CAN communication
Stop lamp switch signal
Receives an operational state of the brake pedal
Output Signal Item Reception unit Signal name Description
ECM
CAN communication
Torque down request signal
Transmits a signal to control the electric throttle control actuator...
Removal and Installation
REMOVALRemove front seat. Refer to Removal and Installation.
Disconnect seat belt buckle harness connector.
Remove seat belt buckle anchor bolt and seat belt buckle.
CAUTION:
Before removing the seat belt buckle anchor bolt, note the positions of washers and spacers for correct installation...