Nissan Murano: Icc/adas (adas Control Unit) / C1b03-4b Cam Abnrml Tmp Detct
DTC Description
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen items
(Trouble diagnosis content) | DTC detection condition |
| |
| C1B03-4B |
CAM ABNRML TMP DETCT
(Camera abnormal temperature detect) |
Diagnosis condition |
-
When engine is running
-
When I-LI system is ON
|
| Signal (terminal) |
— |
| Threshold |
Temperature around lane camera unit is excessively high |
| Diagnosis delay time |
1 second or less |
POSSIBLE CAUSE
FAIL-SAFE
The following systems are canceled:
-
Lane Departure Warning (LDW)
-
Intelligent Lane Intervention (I-LI)
-
Blind Spot Warning (BSW)
-
Rear Cross Traffic Alert (RCTA)
-
Traffic Sign Recognition (TSR)
Confirmation Procedure
DTC CONFIRMATION PROCEDURE
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Start the engine.
-
Turn the I-LI system ON.
-
Perform “All DTC Reading”.
-
Check if the “C1B03–4B” is detected as the current malfunction in self-diagnosis results of “ICC/ADAS”.
Is “C1B03–4B” detected as the current malfunction?
YES>>
Refer to DTC Description.
NO>>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>
Confirmation after repair: Inspection End
DTC Diagnosis Procedure
CHECK LANE CAMERA UNIT SELF-DIAGNOSIS RESULTS
CONSULT
-
Perform “All DTC Reading”.
-
Check if the “C1B00–4B” is detected in “Self Diagnostic Result” of “LANE CAMERA”
Is “C1B00–4B” detected?
YES>>
Refer to DTC Index.
NO>>
GO TO 2.
CHECK ADAS CONTROL UNIT SELF-DIAGNOSIS RESULTS
CONSULT
-
Erase all self-diagnosis results.
-
Perform “All DTC Reading”.
-
Check if the “C1B03-4B” is detected in “Self Diagnostic Result” of “ICC/ADAS”
Is “C1B03-4B” detected?
YES>>
Replace the ADAS control unit. Refer to Removal and Installation.
NO>>
Inspection End
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen items
(Trouble diagnosis content) DTC detection condition
C1B01-55
CAM AIMING INCMP
(Camera aiming incomplete)
Diagnosis condition
When I-LI system is ON
When driving the Nissan Murano vehicle
Signal (terminal)
—
Threshold
Camera aiming is not completed
Diagnosis delay time
10 seconds or more
POSSIBLE CAUSE
Lane camera aiming is not adjusted
Lane camera aiming adjustment has been interrupted
Lane Camera Unit
ADAS control unit
FAIL-SAFEThe following systems are canceled:
Lane Departure Warning (LDW)
Intelligent Lane Intervention (I-LI)
Blind Spot Warning (BSW)
Rear Cross Traffic Alert (RCTA)
Traffic Sign Recognition (TSR)
Confirmation Procedure
DTC CONFIRMATION PROCEDUREPERFORM DTC CONFIRMATION PROCEDURE
CONSULT
Start the engine...
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen items
(Trouble diagnosis content) DTC detection condition
C1B53-97
SIDE RDR R MALF
(Side radar right malfunction)
Diagnosis condition
When engine is running
Signal (terminal)
—
Threshold
ADAS control unit detects that side radar RH has a malfunction...
Other information:
Exploded View
1.
Front combination lamp
Removal and Installation
REMOVALRemove front bumper fascia. Refer to Removal and Installation.
Remove front combination lamp bolts.
Pull front combination lamp forward.
Disconnect harness connectors from front combination lamp and remove...
System Description
SYSTEM DIAGRAMAV Control Unit Input Signal (AV Communication)Transmit unitSignal name
Combination meter
Steering switch signal
AV Control Unit Input Signal (CAN Communication)Transmit unitSignal name
BCM
Door switches state signal
Combination meter
Nissan Murano Vehicle speed signal
Hand brake switch signal
ECM
Engine RPM Signal
IPDM E/R
Battery voltage signal
AUDIO SYSTEMThe audio system consists of the following components:
AV control unit
Instrument panel tweeters
Front door speakers
Rear door speakers
Front auxiliary input jacks
Front auxiliary input jacks control unit
Microphone
Steering switches
Combination meter
Combination switch (spiral cable)
Accessory relay-2
Antenna base (AM/FM antenna, antenna amp...
Categories

The autolight system allows the headlights
to turn on and off automatically. The autolight
system can:
Turn on the headlights, front parking,
tail, license plate and instrument panel
lights automatically when it is dark.
Turn off all the lights (except daylight
running lights) when it is light.
Keep all the lights on for a period of time
after you place the ignition switch in the
OFF position and all doors are closed.
read more