Nissan Murano: Road Wheels & Tires :: Dtc/circuit Diagnosis / C1761 Temperature Data Fl
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.
-
Activate and display TPMS sensor IDs
-
Display tire pressure reported by the TPMS sensor
-
Read TPMS DTCs
-
Register TPMS sensor IDs
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| C1761 |
TEMPERATURE DATA FL (Temperature data front left) |
Diagnosis condition | When ignition switch ON. |
| Signal (terminal) | Temperature data signal (—). | ||
| Threshold | Malfunction in the tire temperature data from the front LH wheel tire pressure sensor. | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
-
Tire pressure sensor
-
BCM
FAIL-SAFE
—
PERFORM SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of "BCM(AIR PRESSURE MONITOR)".
-
Check DTC.
Is DTC “C1761” detected?
YES>>Refer to DTC Diagnosis Procedure.
NO>>Prior to repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.
-
Activate and display TPMS sensor IDs
-
Display tire pressure reported by the TPMS sensor
-
Read TPMS DTCs
-
Register TPMS sensor IDs
PERFORM BCM SELF DIAGNOSTIC RESULT
CONSULT
-
Replace applicable tire pressure sensor. Refer to Removal and Installation.
-
Select “Self Diagnostic Result” mode of "BCM(AIR PRESSURE MONITOR)".
-
Check DTC.
Is DTC “C1761” detected?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Inspection End.
C1735 Ign Circuit Open
DTC Description
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information...
C1769 Config Setting
DTC Description
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: U1010 Control Unit(can)
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition U1010 CONTROL UNIT(CAN) [Control unit (CAN)] Diagnosis condition When ignition switch ON. Signal (terminal) — Threshold — Diagnosis delay time 2 seconds or more POSSIBLE CAUSEBCMFAIL-SAFE— DTC Diagnosis Procedure Replace BCM When DTC U1010 is detected, replace BCM...
Nissan Murano (Z52) 2015-2024 Service Manual: System. Active Grille Shutter System
System Description SYSTEM DIAGRAMSystem DescriptionWhile driving, the active grille shutter system closes shutter to reduce air flow to engine compartment for the purpose of reducing aerodynamic drag, and as a result, improves the Nissan Murano vehicle's fuel efficiency...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- System malfunction
- Warning lights
- Rear bench seat adjustment
- New on site
- Most important about car
Vehicle security system
Your vehicle has two types of security systems:
Vehicle security system NISSAN Vehicle Immobilizer SystemThe vehicle security system provides visual and audible alarm signals if someone opens the doors, liftgate or the hood when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.
