Nissan Murano: Road Wheels & Tires :: Dtc/circuit Diagnosis / C1735 Ign Circuit Open
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.
-
Activate and display TPMS sensor IDs
-
Display tire pressure reported by the TPMS sensor
-
Read TPMS DTCs
-
Register TPMS sensor IDs
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| C1735 |
IGN CIRCUIT OPEN (Ignition circuit open) |
Diagnosis condition | When ignition switch ON. |
| Signal (terminal) | — | ||
| Threshold | BCM has detected a mismatch between IGN ON signals. | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
BCM
FAIL-SAFE
—
PERFORM SELF DIAGNOSTIC RESULT
CONSULT
-
Ignition switch ON.
-
Select “Self Diagnostic Result” mode of "BCM(AIR PRESSURE MONITOR)".
-
Check DTC.
Is DTC C1735 detected?
YES>>Refer to DTC Diagnosis Procedure.
NO>>Inspection End.
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.
-
Activate and display TPMS sensor IDs
-
Display tire pressure reported by the TPMS sensor
-
Read TPMS DTCs
-
Register TPMS sensor IDs
CHECK CAN IGNITION SIGNAL
CONSULT
-
Select “IGN RLY1-F/B” in “Data Monitor” mode of "BCM(INTELLIGENT KEY)".
-
Check that the function operates normally according to the following conditions:
Monitor item Displayed value IGN RLY1 F/B On with ignition in ON position
Is the inspection result normal?
YES>>GO TO 2.
NO>>Check CAN system. Refer to Trouble Diagnosis Flow Chart.
CHECK BCM POWER SUPPLY AND GROUND
Check BCM power supply and ground. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness or connectors.
DRIVE Nissan Murano Vehicle
CONSULT
Clear DTC and test drive vehicle to check for low tire pressure warning lamp.
Does the Nissan Murano vehicle operate without any low tire pressure warning lamp?
YES>>Inspection End.
NO>>Replace BCM. Refer to Removal and Installation.
C1734 Control Unit
DTC Description
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information...
C1761 Temperature Data Fl
DTC Description
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Evap Canister Vent Control Valve
Exploded View 1. EVAP canister control pressure sensor 2. EVAP canister 3. EVAP canister purge hose 4. EVAP canister vent control valve A. O-ring Removal and Installation NOTE: The EVAP canister vent control valve can be removed without removing the EVAP canister...
Nissan Murano (Z52) 2015-2024 Service Manual: P2119 Electric Throttle Control Actuator
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2119 ETC ACTR-B1 (Throttle actuator control throttle body range/performance) 1 Diagnosis condition — Signal (terminal) — Threshold Electric throttle control actuator does not function properly due to the return spring malfunction Diagnosis delay time — 2 Diagnosis condition — Signal (terminal) — Threshold Throttle valve opening angle in fail-safe mode is not in specified range Diagnosis delay time — 3 Diagnosis condition — Signal (terminal) — Threshold ECM detects that the throttle valve is stuck open Diagnosis delay time — POSSIBLE CAUSE Electric throttle control actuator FAIL-SAFE Engine operating condition in fail-safe mode Fail safe mode Nissan Murano Vehicle behavior Electric throttle control actuator (When electric throttle control actuator does not function properly due to the return spring malfunction:) ECM controls the electric throttle actuator by regulating the throttle opening around the idle position...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Warning lights
- Checking engine oil level
- Vehicle Dynamic Control (VDC) OFF switch
- New on site
- Most important about car
Driver and passenger supplemental knee air bag
Driver’s side
The knee air bag is located in the knee bolster, on the driver’s and passenger’s side. All of the information, cautions and warnings in this manual apply and must be followed. The knee air bag is designed to inflate in higher severity frontal collisions, although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain collisions.
Passenger’s side
