Nissan Murano: Road Wheels & Tires :: Dtc/circuit Diagnosis / C1769 Config Setting

Nissan Murano (Z52) 2015-2024 Service Manual / Suspension / Road Wheels & Tires :: Dtc/circuit Diagnosis / C1769 Config Setting

DTC Description

NOTE:

The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1769

CONFIG SETTING

(Configuration setting)
Diagnosis condition When ignition switch ON.
Signal (terminal) —
Threshold
  • Tire pressure monitoring system configuration has not been performed.

  • Receiver ID registration cannot be performed.

Diagnosis delay time —

POSSIBLE CAUSE

  • Configuration is not completed.

  • The ID registration is not completed.

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of "BCM(AIR PRESSURE MONITOR)".

  3. Check DTC.

Is DTC “C1769” detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

Prior to repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

NOTE:

The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

BCM CONFIGURATION

Perform configuration. Refer to Work Procedure.

>>

GO TO 2.

TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to Work Procedure.

Does low tire pressure warning lamp turn OFF?

YES>>

Inspection End.

NO>>

Perform configuration tire pressure monitoring system again. Refer to Work Procedure.

    C1761 Temperature Data Fl

    DTC Description NOTE: The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information...

    Low Tire Pressure Warning Lamp

    Component Function Check CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second, when the ignition switch is placed ON...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: Charging System :: Symptom Diagnosis. Charging System


    Symptom Table Symptom Reference Battery discharged. Refer to Work Flow (With 165-DSS-5000P), or (Without 165-DSS-5000P). The charge warning lamp does not illuminate when ignition switch ON. The charge warning lamp does not turn OFF after the engine starts...

    Nissan Murano (Z52) 2015-2024 Service Manual: C1205 4wd Actuator Relay


    DTC Description DTC DETECTION LOGICMalfunction has been detected from AWD actuator relay integrated with AWD control unit, or malfunction related to AWD solenoid has been detected. DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1205 4WD ACTUATOR RLY (4WD actuator relay) Diagnosis condition Ignition switch: ON Signal — Threshold — Diagnosis delay time — POSSIBLE CAUSE Internal malfunction of AWD control unit Malfunction of AWD solenoid power supply circuit (ground short) FAIL-SAFEFront-wheel drive or shifts to 4-wheel drive (rear-wheels still have some driving torque)...

    Categories

    Seatback pockets

    Nissan Murano. Seatback pockets

    Theremaybe one or two seatback pockets located on the back of the driver and passenger seats. The pockets can be used to store maps.

    WARNING

    read more

     
    Copyright © 2026 www.nimurano.com