Nissan Murano: Dtc/circuit Diagnosis / B2ef0 Internal Battery
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| B2EF0 |
INTERNAL BATTERY (Internal battery) |
CIRC VOLT BELOW THRESHOLD | Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | |||
| Threshold | TCU internal malfunction | |||
| Diagnosis delay time | Less than 1 second | |||
| INTERNAL ELECTRONIC ERROR | Diagnosis condition | When ignition switch is ON. | ||
| Signal (terminal) | — | |||
| Threshold | TCU internal malfunction | |||
| Diagnosis delay time | Less than 1 second | |||
| INCORRECT CMPNENT INSTALLED | Diagnosis condition | When ignition switch is ON. | ||
| Signal (terminal) | — | |||
| Threshold | TCU internal malfunction | |||
| Diagnosis delay time | Less than 1 second | |||
| OVER TEMPERATURE | Diagnosis condition | When ignition switch is ON. | ||
| Signal (terminal) | — | |||
| Threshold | TCU internal malfunction | |||
| Diagnosis delay time | Less than 1 second | |||
POSSIBLE CAUSE
TCU
FAIL-SAFE
Telematics system function stops
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch ON.
-
Erase DTC.
-
Select “Self Diagnostic Result” mode of “TELEMATICS”.
-
Check DTC.
Is DTC B2EF0 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
CONFIRM DTC
Confirm which DTC is detected.
Is DTC B2EF0 [CIRC VOLT BELOW THRESHOLD] detected ?
YES>>GO TO 2.
NO>>GO TO 3.
CHARGE INTERNAL BATTERY
-
Start engine.
-
Run engine for 30 minutes to allow TCU internal battery to charge.
>>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform DTC confirmation procedure again. Refer to DTC Confirmation Procedure.
Is DTC B2EF0 detected again?
YES>>Replace TCU. Refer to Removal and Installation.
NO>>Inspection End.
B2e33 Ecall Button
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
B2E33
ECALL BUTTON
(Ecall button)
Diagnosis condition
When ignition switch is ON...
U1000 Can Comm Circuit
DTC Description
DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real-time application. It is an on-Nissan Murano vehicle multiplex communication line with high data communication speed and excellent error detection ability...
Other information:
Nissan Murano (Z52) 2015-2024 Service Manual: Fluid Cooler Hose
Exploded View 1. Transaxle assembly 2. Hose clamp 3. CVT fluid cooler hose A 4. Hose clip 5. CVT fluid cooler hose B 6. Connector tube 7. CVT fluid cooler hose C 8 Oil warmer A. To radiator. Refer to Exploded View...
Nissan Murano (Z52) 2015-2024 Service Manual: Diagnosis System [distance Sensor (icc Sensor)]
CONSULT Function (LASER/RADAR) APPLICATION ITEMSCONSULT performs the following functions via CAN communication with ADAS control unit and the communication with distance sensor (ICC sensor). Diagnosis mode Description Self Diagnostic Result Displays malfunctioning system memorized in distance sensor (ICC sensor) Data Monitor Displays real-time input/output data of distance sensor (ICC sensor) Work support It can monitor the adjustment direction indication in order to perform the radar adjustment operation smoothly ECU Identification Displays distance sensor (ICC sensor) part number CAN Diag Support Monitor The results of transmit/receive diagnosis of ITS communication can be read...
Categories
- Manuals Home
- Nissan Murano Owners Manual
- Nissan Murano Service Manual
- Memory storage function (key-link)
- How to enable/disable the LDW system
- Intelligent Forward Collision Warning (I-FCW)
- New on site
- Most important about car
Front manual seat adjustment (if so equipped)
Your vehicle seats can be adjusted manually. For additional information about adjusting the seats, refer to the steps outlined in this section.
Forward and backward
