Nissan Murano: Security Control System :: Dtc/circuit Diagnosis / B2603 Shift Posi Status

Nissan Murano (Z52) 2015-2024 Service Manual / Body Exterior, Doors, Roof & Vehicle Security / Security Control System :: Dtc/circuit Diagnosis / B2603 Shift Posi Status

DTC Description

DTC DETECTION LOGIC

NOTE:

If DTC B2603 is displayed with DTC B2601, first perform the trouble diagnosis for DTC B2601. Refer to DTC Description.

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition
B2603

SHIFT POSI STATUS

(Shift position status) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold

BCM detects the following status when ignition switch is in the ON position:

  • P (Park) position signal from TCM: approx. 0V

  • CVT shift selector (detent switch) signal: approx. 0V
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connector

    [CVT shift selector (detent switch) circuit is open or shorted.]

  • Harness or connectors

    (TCM circuit is open or shorted.)

  • CVT shift selector (detent switch)

  • CVT assembly (TCM)

  • BCM

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE 1

CONSULT

  1. Shift the selector lever to the P (Park) position.

  2. Ignition switch ON and wait 1 second or more.

  3. Select “Self Diagnostic Result” mode of “BCM”.

  4. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE 2

CONSULT

  1. Shift the selector lever to any position other than P (Park) and wait 1 second or more.

  2. Select “Self Diagnostic Result” mode of “BCM”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

CHECK CVT SHIFT SELECTOR FUNCTION

  1. Ignition switch ON.

  2. Select “DETE/CANCL SW” and “SFT PN/N SW” in “Data Monitor” mode of “BCM(INTELLIGENT KEY)”.

  3. Check “DETE/CANCL SW” and “SFT PN/N SW” indication under the following conditions:

    Monitor item Condition Indication
    DETE/CANCL SW CVT Shift selector In any position other than P (Park) ON
    P (Park) OFF
    SFT PN/N SW CVT Shift selector In any position other than P (Park) OFF
    P (Park) ON

Is the inspection result normal?

YES>>

Refer to Intermittent Incident.

NO>>

If “DETE/CANCL SW” is incorrect. GO TO 6.

NO>>

If “SFT PN/N SW” is incorrect. GO TO 2.

CHECK BCM INPUT SIGNAL

  1. Ignition switch ON.

  2. Check voltage between BCM harness connector and ground.

    (+) (–) Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    M18 39 Ground Selector lever P or N position Battery voltage
    Other than above 0 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK BCM INPUT SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect BCM connector, transmission range switch connector and ECM connector F79.

  3. Check continuity between transmission range switch harness connector and BCM harness connector.

    Transmission range switch BCM Continuity
    Connector Terminal Connector Terminal
    F29 10 M18 39 Yes

  4. Check continuity between transmission range switch harness connector and ground.

    Transmission range switch Ground Continuity
    Connector Terminal
    F29 10 No

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

REPLACE BCM

  1. Replace BCM. Refer to Removal and Installation.

  2. Perform initialization of BCM and registration of all Intelligent Keys. Refer to Work Procedure.

>>

Inspection End.

CHECK DTC OF TCM

CONSULT

Select “Self Diagnostic Result” mode of “TRANSMISSION”.

Is DTC detected?

YES>>

Perform the trouble diagnosis related to the detected DTC. Refer to DTC Index.

NO>>

Perform the trouble diagnosis related to the TCM power and ground circuits. Refer to Diagnosis Procedure.

CHECK CVT SHIFT SELECTOR POWER SUPPLY

  1. Ignition switch OFF.

  2. Disconnect CVT shift selector (detent switch) connector.

  3. Check voltage between CVT shift selector (detent switch) harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    CVT shift selector (detent switch)
    Connector Terminal
    M78 5 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

GO TO 7.

CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT

  1. Disconnect BCM connector.

  2. Check continuity between CVT shift selector (detent switch) harness connector and BCM harness connector.

    CVT shift selector (detent switch) BCM Continuity
    Connector Terminal Connector Terminal
    M78 5 M19 69 Yes

  3. Check continuity between CVT shift selector (detent switch) harness connector and ground.

    CVT shift selector (detent switch) Ground Continuity
    Connector Terminal
    M78 5 No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK CVT SHIFT SELECTOR CIRCUIT

  1. Disconnect BCM connector and IPDM E/R connector E119.

  2. Check continuity between CVT shift selector (detent switch) harness connector and BCM harness connector.

    CVT shift selector (detent switch) BCM Continuity
    Connector Terminal Connector Terminal
    M78 6 M18 20 Yes

  3. Check continuity between CVT shift selector (detent switch) harness connector and ground.

    CVT shift selector (detent switch) Ground Continuity
    Connector Terminal
    M78 6 No

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace harness.

CHECK CVT SHIFT SELECTOR (DETENT SWITCH)

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Replace CVT shift selector. Refer to Removal and Installation.

REPLACE BCM

  1. Replace BCM. Refer to Removal and Installation.

  2. Perform initialization of BCM and registration of all Intelligent Keys. Refer to Work Procedure.

>>

Inspection End.

Component Inspection

CHECK CVT SHIFT SELECTOR (DETENT SWITCH)

  1. Ignition switch OFF.

  2. Disconnect CVT shift selector (detent switch) connector.

  3. Check continuity between CVT shift selector (detent switch) terminals.

    CVT shift selector (detent switch) Condition Continuity
    Terminal
    5 6 Selector lever P (Park) position No
    Other than above Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace CVT shift selector. Refer to Removal and Installation.

    B2602 Shift Position

    DTC Description DTC DETECTION LOGICNOTE: If DTC B2602 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to DTC Description...

    B2604 Pnp/clutch Sw

    DTC Description DTC DETECTION LOGICNOTE: If DTC B2604 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to DTC Description...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: P17f1 Cvt Judder (c/v Inspection)


    DTC Description NOTE: The customer reports CVT judder (shake, shudder, single or multiple bumps or vibration) hesitation on acceleration, lack of power or RPM flare. If DTC P17F1 is detected on his/her Nissan Murano vehicle, this diagnosis is required...

    Nissan Murano (Z52) 2015-2024 Service Manual: Electronic Controlled Engine Mount


    System Description SYSTEM DIAGRAMSYSTEM DESCRIPTIONThe ECM controls the engine mount operation corresponding to the engine speed. The control system has a 2-step control [Soft/Hard] Vehicle condition Engine mount control Engine speed: Below 950 rpm Soft Engine speed: Above 950 rpm Hard ELECTRONIC CONTROLLED ENGINE MOUNT LINE DRAWING Electronic controlled engine mount control solenoid valve Intake manifold collector     : From next figure Front electronic controlled engine mount Rear electronic controlled engine mount     : To previous figure NOTE: Do not use soapy water or any type of solvent while installing vacuum hose...

    Categories

    Unfastening the seat belts. Checking seat belt operation

    Unfastening the seat belts

    Nissan Murano. Unfastening the seat belts. Checking seat belt operation

    To unfasten the seat belt, press the button on the buckle Nissan Murano. Unfastening the seat belts. Checking seat belt operation. The seat belt automatically retracts.

    read more

     
    Copyright © 2026 www.nimurano.com