Nissan Murano: Dtc/circuit Diagnosis / B2098 Ign Relay on Circ

Nissan Murano (Z52) 2015-2024 Service Manual / Electrical & Power Control / Power Control System :: Ipdm E/r / Dtc/circuit Diagnosis / B2098 Ign Relay on Circ

DTC Description

  • IPDM E/R operates the ignition relay-1 when it receives an ignition switch ON signal from BCM via CAN communication.

  • Turn the ignition relay-1 OFF by pressing the push-button ignition switch once when the Nissan Murano vehicle speed is 2.5 MPH (4 km/h) or less.

  • Turn the ignition relay-1 OFF with the following operation when the Nissan Murano vehicle speed is more than 2.5 MPH (4 km/h) or when an abnormal condition occurs in CAN communication from the combination meter (Emergency OFF)

    • Press and hold the push-button ignition switch for 2 seconds or more.

    • Press the push-button ignition switch 3 times within 1.5 seconds.

NOTE:

The ignition relay-1 does not turn ON for 3 seconds after emergency OFF even if the push-button ignition switch is pressed.

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition
B2098

IGN RELAY ON CIRC

(Ignition relay ON circuit)
Diagnosis condition When ignition switch ON.
Signal (terminal)
Threshold
Diagnosis delay time 1 second or more

Possible Cause

  • IPDM E/R.

  • Harness or connectors (ignition relay-1 circuit short).

FAIL-SAFE

Turns ON the tail lamp relay for 10 minutes.

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait 1 second or more.

  3. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  4. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

SELF DIAGNOSTIC RESULT

CONSULT

  1. Select “Self Diagnostic Result” mode of “IPDM E/R”.

What is the display history of DTC “B2098”?

“CRNT”>>

GO TO 2.

“PAST”>>

GO TO 5.

CHECK IGNITION RELAY-1 CONTROL CIRCUIT VOLTAGE 1

  1. Ignition switch ON.

  2. Check voltage between IPDM E/R harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    IPDM E/R
    Connector Terminal
    E119 43 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK IGNITION RELAY-1 CONTROL CIRCUIT VOLTAGE 2

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector and BCM connector M19.

  3. Ignition switch ON.

  4. Check voltage between IPDM E/R harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    IPDM E/R
    Connector Terminal
    E119 43 Ground 0 V

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK IGNITION RELAY-1 CONTROL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R Ground Continuity
    Connector Terminal
    E119 43 No

Is the inspection result normal?

YES>>

Perform the diagnosis procedure for DTC B26F2. Refer to DTC Description.

NO>>

Repair or replace harness.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

    U1010 Control Unit(can)

    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition U1010 CONTROL UNIT(CAN) (Control unit CAN) Diagnosis condition When ignition switch ON...

    B2099 Ign Relay Off Circ

    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC Detection Condition B2099 IGN RELAY OFF CIRC (Ignition relay OFF circuit) Diagnosis condition When ignition switch ON...

    Other information:

    Nissan Murano (Z52) 2015-2024 Service Manual: Component Parts. Automatic Emergency Braking System


    Component Parts Location A. Center of windshield behind the auto anti-dazzling inside mirror B. Center of instrument panel (view with center console removed) C. Engine room right side D. Front bumper (center) E. Engine room left side F...

    Nissan Murano (Z52) 2015-2024 Owners Manual: System malfunction


    If the AEB system malfunctions, it will be turned off automatically, a chime will sound, the AEB warning light (orange) will illuminate and the warning message [Malfunction] will appear in the vehicle information display. Action to take If the warning light (orange) comes on, stop the vehicle in a safe location, turn the engine off and restart the engine...

    Categories

    Unfastening the seat belts. Checking seat belt operation

    Unfastening the seat belts

    Nissan Murano. Unfastening the seat belts. Checking seat belt operation

    To unfasten the seat belt, press the button on the buckle Nissan Murano. Unfastening the seat belts. Checking seat belt operation. The seat belt automatically retracts.

    read more

     
    Copyright © 2026 www.nimurano.com