Nissan Murano: Basic Inspection / Additional Service When Replacing Around View Monitor Control Unit

Nissan Murano (Z52) 2015-2024 Service Manual / Driver Information & Multimedia / Audio, Visual & Navigation System :: Intelligent Around View Monitor with Display Audio System / Basic Inspection / Additional Service When Replacing Around View Monitor Control Unit

Description

BEFORE REPLACEMENT

When replacing around view monitor control unit, save or print current vehicle specification with CONSULT configuration before replacement.

NOTE:

If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replacing around view monitor control unit.

AFTER REPLACEMENT

CAUTION:

When replacing around view monitor control unit, you must perform “After Replace ECU” with CONSULT.

Complete the procedure of “After Replace ECU” in order.

If you set incorrect “After Replace ECU”, incidents might occur.

Configuration is different for each Nissan Murano vehicle model. Confirm configuration of each vehicle model.

Work Procedure

SAVING VEHICLE SPECIFICATION

CONSULT

Enter “Re/Programming, Configuration” and perform “Before Replace ECU” to save or print current Nissan Murano vehicle specification.

NOTE:

If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replacing around view monitor control unit.

GO TO 2.

REPLACE AROUND VIEW MONITOR CONTROL UNIT

Replace around view monitor control unit. Refer to Removal and Installation.

GO TO 3.

WRITING Nissan Murano Vehicle SPECIFICATION

CONSULT

Enter "Re/Programming, Configuration".
If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write Nissan Murano vehicle specification. Refer to Work Procedure.
If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configuration" to write Nissan Murano vehicle specification. Refer to Work Procedure.

GO TO 4.

OPERATION CHECK

Check that the operation of the around view monitor control unit and camera images (fixed guide lines and predictive course lines) are normal.

Work End.

Diagnosis and Repair Workflow

Work Flow OVERALL SEQUENCE Reference 1: Refer to CONSULT Function. Reference 2: Refer to DTC Index. Reference 3: Refer to Symptom Table. DETAILED FLOWINTERVIEW AND SYMPTOM CONFIRMATION Check the malfunction symptoms by performing the following items: Interview the customer to obtain the malfunction information (conditions and environment when the malfunction occurred)...

Configuration (around View Monitor Control Unit)

Description Vehicle specification needs to be written with CONSULT because it is not written after replacing around view monitor control unit.Configuration has three functions as follows Function Description READ CONFIGURATION Reads the Nissan Murano vehicle configuration of current around view monitor control unit...

Other information:

Nissan Murano (Z52) 2015-2024 Service Manual: Front Fog Lamp Circuit

Component Function Check CHECK FRONT FOG LAMP OPERATION CONSULT Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R”. While operating the test items, check that the front fog lamp is turned ON. Fog : Front fog lamp ON Off : Front fog lamp OFF Is the inspection result normal? YES>> Front fog lamp circuit is normal...

Nissan Murano (Z52) 2015-2024 Service Manual: P2100 Throttle Control Motor Relay

DTC Description DTC DETECTION LOGIC ECM detects that the voltage of power source for throttle control motor is excessively low. ECM detects that the throttle control motor relay is stuck ON. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2100 ETC MOT PWR-B1 (Throttle actuator “A” control motor circuit/open) Diagnosis condition Start engine and let it idle Signal (terminal) Throttle control motor circuit Threshold ECM detects that the voltage of power source for throttle control motor is excessively low Diagnosis delay time — P2103 ETC MOT PWR-B1 (Throttle actuator “A” control motor circuit high) Diagnosis condition Ignition switch ON Signal (terminal) Throttle control motor circuit Threshold ECM detects that the throttle control motor relay is stuck ON Diagnosis delay time — POSSIBLE CAUSEDTC P2100 Harness or connectors (Throttle control motor relay circuit is open) Throttle control motor relay DTC P2103 Harness or connectors (Throttle control motor relay circuit is shorted) Throttle control motor relay FAIL-SAFE Engine operating condition in fail-safe mode Fail safe mode Nissan Murano Vehicle behavior Throttle control motor relay ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx...