Nissan Murano: Door & Lock :: Dtc/circuit Diagnosis / U1010 Control Unit(can)
DTC Description
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen items
(Trouble diagnosis content) | DTC detecting condition |
| U1010–49 |
CONTROL UNIT(CAN)
[Control unit (CAN)] |
Diagnosis condition |
All times |
| Signal (terminal) |
– |
| Threshold |
Automatic back door control module detected internal CAN communication circuit malfunction |
| Diagnosis delay time |
2 seconds or more |
POSSIBLE CAUSE
Automatic back door control module
FAIL-SAFE
Inhibit automatic back door system all function
DTC Confirmation Procedure
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Ignition switch OFF.
-
Ignition switch ON and wait for 2 seconds or more.
-
Select “Self Diagnostic Result” mode of “AUTO BACK DOOR”.
Is DTC “U1010-49” displayed?
YES>>
Refer to DTC Diagnosis Procedure.
NO>>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>
Confirmation after repair: Inspection End.
Diagnosis Procedure
REPLACE AUTOMATIC BACK DOOR CONTROL MODULE
When DTC “U1010-49” is detected, replace automatic back door control module.
>>
Replace automatic back door control module. Refer to Removal and Installation.
DTC Description
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Murano vehicle multiplex communication line with high data communication speed and excellent error detection ability...
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen items
(Trouble diagnosis content) DTC detecting condition
B2401–86
IGN OPEN
(Ignition open)
Diagnosis condition
All times
Signal (terminal)
Ignition switch ON signal (CAN communication)
Threshold
When all of the following conditions are satisfied
CAN communication is normal
Automatic back door control module receives wake up signal via CAN communication with BCM
Automatic back door control module cannot detect ignition switch ON signal via CAN communication with IPDM E/R
Diagnosis delay time
–
B2401–87
IGN OPEN
(Ignition open)
Diagnosis condition
All times
Signal (terminal)
CAN communication
Threshold
When automatic back door control module can not communicate CAN communication signal
Diagnosis delay time
2 seconds
POSSIBLE CAUSE
CAN communication system
BCM
IPDM E/R
Automatic back door control module
FAIL-SAFEInhibit automatic back door system auto open/close function
DTC Confirmation Procedure
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
Ignition switch ON...
Other information:
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P2119
ETC ACTR-B1
(Throttle actuator control throttle body range/performance)
1
Diagnosis condition
—
Signal (terminal)
—
Threshold
Electric throttle control actuator does not function properly due to the return spring malfunction
Diagnosis delay time
—
2
Diagnosis condition
—
Signal (terminal)
—
Threshold
Throttle valve opening angle in fail-safe mode is not in specified range
Diagnosis delay time
—
3
Diagnosis condition
—
Signal (terminal)
—
Threshold
ECM detects that the throttle valve is stuck open
Diagnosis delay time
—
POSSIBLE CAUSE
Electric throttle control actuator
FAIL-SAFE Engine operating condition in fail-safe mode
Fail safe mode Nissan Murano Vehicle behavior
Electric throttle control actuator
(When electric throttle control actuator does not function properly due to the return spring malfunction:)
ECM controls the electric throttle actuator by regulating the throttle opening around the idle position...
Removal and Installation
REMOVALRemove steering column cover screws (A).
NOTE:
Rotate steering wheel to access steering column cover screws.
Release steering column upper cover pawls using a suitable tool and remove.
: Pawl
Release gap hider (1) pawls from the steering column upper cover (2)...